And finally a new norm is put forward for selecting backlash and tooth thickness deviation of gears.
最后，提出了一种新的侧隙和齿厚偏差选择规范。
Finally, the effect of dispersive and thickness deviation of liquid crystal on wavelength drift is analyzed by analogy.
最后运用类比的方法，分析了液晶色散和液晶厚度偏差对透射波长的影响。
The site application results show that the strategy of Q prediction feedforward AGC has remarkable effect on decreasing thickness deviation of hot strip.
现场实际应用表明，该策略是对抑制热轧带钢厚度偏差具有显著的效果。
The article describes the automatic gauge control, cause of thickness deviation, setup of control models and thickness control and adjustment of the single stand cold plate mills.
介绍单机架冷轧机厚度控制系统、产生厚差的原因、控制模型的建立及厚度的控制和调节。
Fluorescent film thickness tester deviation, or test method error.
荧光膜厚测试仪偏离，或测试方法错误。
Deviation measurement of tooth thickness and conical point of straight bevel gear by using steel bail was studied and approached.
对钢球法测量直齿圆锥齿轮齿厚及锥项位置误差检测进行了研究和探讨。
In case of deviation of the measured average thickness from the specified average value, the Wafer Yield adjustment has to come into force.
万一出现，测量的平均厚度与技术要求的平均厚度出现偏差，晶片的成品率必须进行调整。
Additionally when the very thick veneer is peeled, the mathematical model has been corrected so that the deviation of veneer thickness is decreased.
此外，当旋切大厚度的单板时，对该数学模型进行了修正，以减小单板的厚度偏差。
The thickness of the liquid crystal and the arrangement of liquid crystal molecule are flexible, there are no deviation in the outgoing beams.
滤光片中的液晶厚度、液晶分子的排列方向比较灵活，输出光束不发生偏离。
After analysis of the trouble and disassembly examination, it was first found that the minor deviation of the thickness of the flow guider's grand was the main reason causing the trouble.
经分析原因并对设备进行解体查验，首次发现导流器压盖厚度的微小偏差是产生故障的原因。
The obtained manganese dioxide features uniform thickness, large discharge capability, small deviation and high current efficiency.
所得二氧化锰产品厚度均匀，放电容量大而偏差小，电流效率高。
For the HRG's technology fabrication deviation, effect of the resonator's thickness nonuniformity on the gyro accuracy is studied. The error model is established and the error mechanism is analyzed.
针对半球谐振陀螺仪的工艺制造偏差，研究半球谐振子薄壁厚度不均匀对陀螺精度的影响，建立误差模型，分析误差机理。
The design models of blank of tapered wall thickness cone and equal wall thickness cone with deviation from sine law are presented.
同时给出了考虑偏离正弦律强力旋压等壁厚和变壁厚锥形件毛坯的设计模型。
The deviation of the particleboard's thickness is the crux of the matter for the quality of the board sanding; the particleboard's thickness is controlled strictly during the producing course.
刨花板厚度偏差是影响砂光质量的关键因素，生产过程中必须严格控制刨花板厚度。
Contrasting the average thickness between simulation result and real product, the deviation is only 2.2%, so the reliability of finite element simulation was verified.
将模拟结果与实际产品的平均壁厚对比，偏差仅为2.2%，验证了有限元模拟的可靠性。
Contrasting the average thickness between simulation result and real product, the deviation is only 2.2%, so the reliability of finite element simulation was verified.
将模拟结果与实际产品的平均壁厚对比，偏差仅为2.2%，验证了有限元模拟的可靠性。
应用推荐