Power take - off, squared shaft drive. two stud flange without oil seal gasket.
动力启动方轴传动装置。销法兰。无油密封垫圈。
This makes them ideally suited to deep well applications where traditional shaft drive solutions would be impractical.
在深井用泵场合,传统的轴驱动方案不可用时,该泵即成为您的理想选择。
This performance can only be handle driving a gear shaft to rotate and rack shaft to move, but not gear shaft drive gear shaft to rotate.
这种自锁性能只能是手柄带动着齿轮轴的转动及齿条轴的移动,而不能是齿条轴带动着齿轮轴的转动。
Rolling shutter opening methods are varied, electric remote control, electric button, manual remote pole, pull strap, spring shaft drive and so on.
卷帘窗的开启方式有多种多样,电动遥控、电动按键、手动摇杆、手拉皮带、弹簧轴驱等。
This, combined with its open architecture and standard off-the-shelf products, helps provide improved usability and support over traditional line shaft drive control.
结合其开放式构架和标准原料产品,这样就帮助提供改善了的可用性而且支持传统的动力轴驱动控制。
A comparison of the two drive modes, namely, the front and rear shaft drives, has led to the conclusion that a front shaft drive is more rational for use on industrial boiler chain grates.
最后,对前、后轴两种驱动方式进行了比较,工业锅炉链条炉排采用前轴驱动方式更为合理。
On the way out, these gases drive a turbine which is connected to the fan via a shaft, thus drawing in more air and keeping the process going.
在喷管前有一组涡轮,涡轮与风扇连接在一根轴上。涡轮带动风扇又吸入了更多的空气,这样就产生了连续的循环。
But there are limits to how many blades can be tacked onto the rotor's drive shaft, and once again weight becomes a consideration.
但是安装到旋翼驱动轴上的桨叶数量是有限制的,而且飞机的重量同样需要考虑。
In his application Selden described a machine with a gasoline-driven, combustion-type engine that sat in front of the driver; a clutch; a foot brake; a drive shaft; and front-wheel drive.
申请中,赛尔登描述了一项机器是石油驱动、在驾驶座前有燃烧式发动机;离合器、脚刹车、前轮驱动。
The turbine can drive the ship directly or be used to generate electricity to drive the prop shaft.
涡轮机能够直接推动船前进,又或者产生电力推动传动轴。
The flap or slat drive system in the aircraft according to claim 1, not including a transverse shaft line that extends through said fuselage from one to another of said wings.
皮瓣或金属板驱动系统在飞机根据索赔1,不包括横向轴延伸线,通过机身表示,从一个到另一个的说翅膀。
Electrical synchronization is used in ac drive, often with a balanced motor shaft system to achieve electrical synchronization.
电气同步是在交流传动中,常用带有均衡电动机的电轴系统来实现电气同步。
This, the team suggests, implies that the direction of rotation is programmed into the stator ring, rather than the shaft, which thus dictates the direction of drive.
这一点,研究人员的看法,暗示旋转方向是规划到定子环,而不是轴,从而指引驱动器的方向。
These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.
这些驱动器,中央螺旋桨轴通过减少锥齿轮2:1减少。
Gear a, at the end of the drive shaft, and gear B, on the countershaft, are in constant mesh.
齿轮A位于驱动轴的末端,齿轮b在副传动轴上,它们恒定啮合。
During the start and stop of the drive shaft, the swing frame of the soft support will have a very obvious vibration.
在传动轴启动和停转的过程中,软支承的摆架会有非常明显的振动,硬支承的摆架则没有这种现象。
Pump wear parts are mainly drive shaft and bushing, passive gear center hole and shaft pin, pump shell lumen and gear, gear face and pump cover, etc.
齿轮泵的磨损部位主要有主动轴与衬套、被动齿轮中心孔与轴销、泵壳内腔与齿轮、齿轮端面与泵盖等。
The gear section also has the input shaft and the output shaft needed to transmit power to the drive wheels.
齿轮段也有输入轴和输出轴,它必须吧动力传递给驱动轮。
For the drive shaft balancing machine, the hard bearing can achieve the accuracy is far beyond the actual needs.
对于传动轴平衡机来说,硬支承所能达到的精度也远远超出了实际需要。
The suspension can turn winding it's axle line, the wire rope winding on the rope roller drive the suspension tools by the suspension shaft.
吊杆架可绕自身轴线回转,手摇起重机绳筒上缠绕的钢丝绳通过吊杆架带动吊具。
If it is found that the accuracy of a drive shaft balancing machine can not meet the requirements, it must be the result of other factors.
如果发现一台传动轴平衡机的精度不能满足要求,那一定是其它因素造成的结果。
Drive shaft a drive shaft and universal joints connect the transmission to the rear drive axle on most rear-wheel-drive vehicles.
传动轴在大多数后轮驱动的车辆中主要是靠传动轴和万向节连结着变速箱与后轮驱动桥。
Butterfly valve through the valve shaft rotation to drive the rotation of a disc-shaped disc, to open and close a valve, cut off from the main pipe and throttle with.
进口蝶阀是指通过阀轴旋转来带动一个圆盘形的蝶板的转动,达到开启与关闭的一种阀门,在管道上主要起切断和节流用。
Available in either thru-shaft or end-of shaft models, it is specifically designed to provide feedback for ac and DC drive control systems.
可在任何直连轴或最终的轴模型,它是专为交流和直流传动控制系统的反馈。
Available in either thru-shaft or end-of shaft models, it is specifically designed to provide feedback for ac and DC drive control systems.
可在任何直连轴或最终的轴模型,它是专为交流和直流传动控制系统的反馈。
应用推荐