If so, turn the ignition switch in the on position, put the car in two gear, foot clutch, vehicle drag, when traveling to a certain speed, release the clutch, the car would start.
如果是这样,拧动点火开关在ON的位置,把车挂二挡,脚踩离合,用车拖拽,当行驶到一定速度时,松开离合,汽车就能自然启动。
Another way of doing it is to release the clutch until the moment during which the engine revs down a little and then applying pressure on the accelerator.
另一种方法是,释放离合器,直至引擎转速略有下降,然后,踏下加速踏板。
In some cars the driver has to step on a pedal to release the clutch, then shift the gears with a lever.
一些汽车的驾驶员用脚踩踏板来松开离合器,然后再用变速杆来换档。
It is forbidden to operate the power take off's switch under the condition of the clutch not apart. release the clutch should be slow.
禁止在离合器未分离的情况下操纵取力器开关。松开离合器踏板的动作要缓慢。
When the clutch pedal is pressed, a cable or hydraulic piston pushes on the release fork, which presses the throw-out bearing against the middle of the diaphragm spring.
当离合器踏板按下时,电缆或者液压活塞将推动离合器分离叉杆,离合器分离叉杆推着外伸的轴承贴在膜片弹簧的中间。
Release the clutch while maintaining constant pressure on the accelerator.
放掉离合器,踩油门保持匀速。
Claim statistical data indicated that truck clutch release bearing had high failure rate, the failure mode including abnormal noise, ablation, oil starvation and wear of bearing block shoulder, etc.
统计近几年的三包索赔产品看出,某载货车离合器分离轴承的故障率一直居高不下,主要故障形式有轴承异响、烧蚀、缺油、轴承座耳台肩磨损等。
Various models, clutch pressure plate assembly, platen assembly, release bearing professional build high quality clutch, involving subcompact car pickup trucks, such as more than 500 kinds of models.
各车型、离合器压盘总成,从动盘总成、分离轴承专业打造高品质离合器、涉及微型车轿车皮卡车货车、等500多种车型。
Instructor: Fantastic. OK. Start the 3 ignition. the car starts. Now, take a deep breath and release the 4 clutch.
教练:好极了。那么,点火吧。(车开动了。)现在,深呼吸然后放开离合器。
When sewing machine work on standby, motor by clutch release load, to continue running light, caused a great deal of standby loss.
在缝纫机待料待机时,电机通过离合器脱开负载,继续空载运行,造成极大的待机损耗。
The fork moves the release bearing into the center of the pressureplate. This causes the pressure plate face to pull away from the clutch disc, releasing thedisc from the flywheel.
拨叉带动分离轴承进人压盘中部,从而使压盘和离合器盘分离,离合器盘和发动机飞轮分离。
The fork moves the release bearing into the center of the pressureplate. This causes the pressure plate face to pull away from the clutch disc, releasing thedisc from the flywheel.
拨叉带动分离轴承进人压盘中部,从而使压盘和离合器盘分离,离合器盘和发动机飞轮分离。
应用推荐