• Reaming is one of the finish machining methods of hole.

    铰孔精加工手法之一

    youdao

  • The principle of pulse electrochemical finish machining (PECFM) is discussed.

    阐述脉冲电化学光整加工原理。

    youdao

  • The adjustment, clamping and machining method in finish machining are summarized.

    总结了精加工调整装夹加工方法

    youdao

  • The finish machining can be completed in one machine tool by milling and rolling.

    通过铣削滚压机床完成球面精加工。

    youdao

  • These methods have been used in finish machining during assembling components of aircraft.

    这些方法飞机部件装配精加工获得应用

    youdao

  • Based on analyzing the mechanism of pulse electrochemical finish machining, a practical experiment is designed.

    分析研究脉冲电化学光整加工原理基础之上,结合实际进行了实验设计。

    youdao

  • The goal of finish machining is achieved and surface roughness is reduced 3 ~ 5 grades based on experimental data.

    根据实验得到优选数据进行加工,有效地降低了表面粗糙度3 ~5,达到了光整加工目的

    youdao

  • The volt ampere properties of electrolyte in pulse electrochemical finish machining (PEFM) are investigated in this paper.

    脉冲电化学光整加工(PEFM )中所采用的一种电解液伏安特性进行了实验研究

    youdao

  • Mechanical Finish Machining has the question of low productivity and high cost. Therefore, it can't satisfy the practical production.

    由于目前加工方法主要是机械光整加工,存在着加工质量生产率成本问题

    youdao

  • Grinding gear with the toroidal involute interior thread worm grind wheel is a new kind of process in hard surface gear finish machining.

    渐开包络螺纹蜗杆砂轮齿齿面齿轮精加工的新型工艺

    youdao

  • Grinding gear with the toroidal involute interior thread worm grind wheel is a new kind of process in hard surface gear finish machining.

    针对齿轮齿磨削加工存在的困难,提出用蜗杆砂轮磨削的双参数法来磨削面齿轮

    youdao

  • The finish machining of the bisect plane of bisect sliding bearing is the key working procedure of the machining process of such products.

    对开滑动轴承对接平面精加工该类产品工艺流程关键工序

    youdao

  • There is an obvious disparity between our nation and other developed nations in the field of hard surface finish machining of the spiral bevel gear.

    螺旋锥齿轮齿精加工这一环节上我国发达国家差距尤为明显

    youdao

  • Our factory has a 300-ton punch, two 100-ton, 200-ton punches respectively. It is our feature that products are forged and treated by finish machining.

    我厂300吨位冲床一台,100顿,200冲床2台,产品经热后再精加工我厂特色

    youdao

  • The problem of slender pieces deformation and the vibration error is one of the key techniques that whirling should solve when using in finish machining.

    旋风铣削法一种较先进高效率加工螺纹方法 ,适用批量较大的螺纹粗加工。

    youdao

  • Based on the geometry characteristic and processing technique of centrifugal compressor impeller, the tool path of rough and finish machining are scheduled.

    分析离心压气机叶轮几何结构特点加工工艺,并此基础上规划叶轮精加工刀具轨迹

    youdao

  • To solve this pivotal problem, the design of special device to finish machining the sealing surface of soldered pipe board and bundles in locale becomes urgent.

    针对问题设计一种能现场管束焊装密封面进行精加工处理的专用装置

    youdao

  • According to the geometrical data of a three-dimensional model, finish machining strategy with section plane method is adopted on the basis of the offset surface.

    根据三维造型数据采用基于等距面的平面进行精加工。

    youdao

  • The experimental and analytical results show that the new posture following and keeping fixture can meet the requirements of aircraft assembly and finish machining.

    试验应用分析表明这种新的动固持方法可以满足机身对接装配精加工要求

    youdao

  • Also the new technology of finish machining for pipe die has been established, the approaches to increase the machining efficiency of the pipe die have been raised as well.

    制订了新的管模精加工工艺,并提出提高管模产品加工效率途径

    youdao

  • Introduces the analysis on technological processes for the spindle of machining center TKP6511, improves the technological design of semi-finish machining and finish machining.

    通过对加工中心TKP6511主轴加工工艺过程分析改进其半精加工及精加工工艺设计

    youdao

  • Results showed that ferrite net and lower hardness due to low cooling rate, coarser finish machining resulted in the fracture during earlier stage of rotary bending fatigue test.

    结果表明冷却不足使组织中出现网状块状素体,导致硬度偏低加之磨削加工痕迹较粗是引起轮毂早期断裂原因。

    youdao

  • Our conclusion is that the ultrasonic drilling or ultrasonic reaming is suitable for finish machining of holes and a promising process to be used in machining aluminum and car bon steels.

    因此超声波钻削乃至铰削精加工方面一种有前途工艺方法。

    youdao

  • GPFM Ambition: Learn from foreign advanced food product linmanufacture food machine suitable for home corporation, dedicate intelligence and force to finish machining China farm products.

    我们的志向:不断向国外先进食品生产线学习,制造适合国内企业的食品加工设备,为中国食品的深加工奉献智慧力量

    youdao

  • Based on the characteristics about pulse electrochemical finish machining (PEFM), its mechanism is studied. According to finish machining principles the experimental design is carried out.

    论述脉冲电化学光整加工特点研究脉冲电化学光整加工机理根据加工原理进行实验设计

    youdao

  • The technical equipment adopted the construction that the spindle drove boring sleeve, boring bar and cutter bar in order to finish machining spherical surface. The improved result was good.

    工装采用主轴带动和镗结构完成球面加工的切削运动,已取得了良好的使用效果

    youdao

  • Requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. So, finish machining and parameter-set are necessary.

    液压转向机对齿条杆部表面很高耐磨储油封存要求,为此需要一套表面超精加工工艺加工参数设定。

    youdao

  • Requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. So, finish machining and parameter-set are necessary.

    液压转向机对齿条杆部表面很高耐磨储油封存要求,为此需要一套表面超精加工工艺加工参数设定。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定