First, we build a fault diagnosis and fault-tolerant control of a specific model of the torpedo.
首先是建立了一套故障诊断和容错控制研究专用的水下航行器模型。
This paper deals with fault tolerant control of a Networked control Systems (NCS) problem with network delay.
本文是针对一类有网络延时的网络化控制系统,研究其故障容错控制问题。
The intension of concept of reliability and the definition of reliability are discussed according to whether the fault tolerant control system satisfies performance requirement.
以是否满足性能指标要求为评判标准,研究了容错控制系统可靠性概念的内涵和定义。
The fault probability, the degree of fault tolerance and problem of reliabilty in the fault tolerant control system are analyzed in the view of statistics.
基于系统的状态划分,以统计理论的观点分析了容错控制系统中的故障概率、容错能力和可靠性问题。
Transmit power control technology contributes as a fundamental part in fault tolerant topology control, through which reliably-connected and highly efficient topology can be constructed.
功率控制技术是容错拓扑控制中的重要手段,可以简化网络结构,获得可靠连通和高效的底层拓扑。
A decoupling controller and an approach to the allocation of thruster forces of an AUV are investigated first, then a fault-tolerant control approach under thruster fault is given.
文中先给出在正常情况下水下机器人的解耦控制器及推力分配,然后给出了在推力器出现故障时的容错控制策略。
A fault diagnosis and fault-tolerant control scheme using adaptive observer is generalized to near space hypersonic vehicle (NSHV) to deal with actuator fault.
提出了一种基于自适应观测器的故障诊断与容错控制策略,应用到近空间高超声速飞行器(NSHV)上处理执行器故障。
The problem of robust fault-tolerant control for networked control systems (NCS) with uncertain time-delay and uncertain parameter is studied.
研究了一类具有网络诱导时延和参数不确定性网络化控制系统鲁棒容错控制问题。
On account of characteristic of every part, it designs suitable measure of fault tolerant control for them.
针对各部分故障的特点,为每一部分设计了合适的故障容错控制方法。
The robust fault-tolerant control problem is studied for uncertain linear discrete systems.
研究了线性离散不确定系统的鲁棒容错控制问题。
The fault-tolerant control of electronic fuel injection (EFI)engine plays an important role in improving its emission and economy performance.
电喷汽车发动机的容错控制对于改善汽车发动机的排放、经济性有重要作用。
A new method of fault tolerant control for multiloop SOSI system is suggested.
本文针对单输入单输出的多回路系统提出了一种简单可行的容错控制方法。
The result shows that the algorithm, which has better adaptability, can fulfill the demand of fault tolerant control in fault system with single sensor failure.
结果表明,该控制策略可以满足有单个传感器失效的故障系统容错控制要求,具有更强的适应性。
The research results in the dissertation can be used in engineering design of fault diagnosis and fault-tolerant control of fin stabilizer systems.
本文的研究工作可为减摇鳍故障诊断与容错控制工程设计应用。
Generally, passive and active fault tolerant control systems depend on system models-quantitative, qualitative or quasi - quantitative.
被动容错控制和主动容错控制多依赖于系统的模型:定量,半定量或定性模型。
Fault diagnosis and fault-tolerant control are successfully applied in many important engineering areas.
近年来故障诊断与容错控制在各种重要的工程技术领域得到了成功的应用。
This paper studies a fault-tolerant control system for a space modular manipulator system mounted on space station or other spacecrafts such as satellites, located in low earth orbit.
研究搭载在空间站或其他近地轨道航天器上的空间模块化机械手系统的容错控制系统。
An unified methodology for the fault detection and the fault tolerant control based on iterative learning observer (ILO) is presented.
提出了一种基于迭代学习观测器(ILO)将故障检测和容错控制进行统一设计的方法。
The robust fault-tolerant control problem of linear discrete system is discussed in this paper.
讨论了离散线性系统的鲁棒容错控制问题。
This paper proposes a new algorithm of fault tolerant control: Minimum Variance Control on Random Parameter.
提出了一种新的容错控制方案:随机参数最小方差控制。
Therefore, it is very important to determine the degree of importance of a component in the design process of a fault-tolerant control system.
因此,在设计容错控制系统时确定部件重要度是非常重要的。
The paper presents the topology and control strategy of a highly fault tolerant induction motor VF speed regulation system.
本文提出一种高容错感应电机变频调速集成系统的拓扑结构和控制策略。
The Markov method is used to analyse the reliability of dual hot - redundant reparable fault tolerant control system, and some calculating formula are derived.
用马尔可夫过程,对双机热冗余可修复容错控制系统的可靠性进行了分析,得出了有关的计算公式。
The purpose of this paper is to apply fault tolerant control theories to the design of electro hydraulic servo system in order to raise its reliability.
本文目的旨在把当今前沿的容错控制理论应用到电液伺服系统设计中去,以提高其可靠性。
Firstly, the fault-tolerant process control is introduced according to the safety and economics requirement of chemical, power, iron and steel processes.
首先,从工业生产过程的安全经济运行与控制需要出发,介绍了过程控制中容错的基本思想。
This paper presents a unified fault tolerant control approach for nonlinear systems based on a continuous stirred tank reactor (CSTR).
针对连续搅拌箱式反映器,提出一种闭环非线性系统容错控制的混合方法。
The application of fault tolerant control and information fusion of multi-sensors is studied in this paper for autonomous flight of pilotless helicopters.
研究了将多传感器容错控制和信息融合技术应用于无人直升机的自主飞行控制。
The fault tolerant control is of mini-mum variance control in the case of random parameters and noises.
容错控制是随机参数和随机噪声情况下的最小方差控制。
The D-stable fault-tolerant control problem of discrete time-delay uncertain system is studied.
研究了离散时滞不确定系统的D稳定容错控制问题。
The need of simultaneous stabilization or pole-assignment is due to de-signing fault-tolerant control systems.
同时稳定或极点配置是出于设计容错控制系统之所需。
应用推荐