The cutting force can notably be deduced using the cutting fluid during machining.
在切削加工中，使用切削液能显著降低切削力。
PCD tool is the best tool material for precise machining from points of the cutting force view.
从切削力这一因素来看，PCD是精加工颗粒增强铝复合材料的最佳刀具材料。
The singular index of cutting force signal is proposed as a parameter for detecting cutter's wear.
提出采用切削力信号的奇异性指数作为衡量刀具磨损的参量。
The real-time obtaining of cutting parameters is one of the key technologies of cutting force prediction.
切削用量的实时获取是切削力预测的关键技术之一。
The estimated cutting force and the feedrate are the controlled output and the control input, respectively.
估计的切削力和进刀速度分别是受控的输出和控制输入。
An orthogonal cutting force model with tool flank wear has been analyzed based on cutting test investigation.
在试验研究基础上进行了有后刀面磨损的正交切削模型分析。
Dynamic cutting force of blade was an important parameter reflecting the cutting process during the cut of sugarcane.
甘蔗切割过程中，割刀动态切割力是反映切割过程的一个重要参数。
This paper researches into the unbalance factor of the cutting force and the cutting area in the face-milling process.
本文研究了端面铣削过程的切削力不均衡系数和切削面积不均衡系数。
The distribution of cutting force between driving legs is analysised by establishing of static force equilibrium equations.
通过建立机构的静力平衡方程，分析了切削加工载荷在各条驱动腿之间的分配情况。
The article studies the influence of cutting speed to the cutting force in the foundation of high speed cutting experimentation.
本文在高速车削的试验基础上，研究高速车削时切削速度对切削力的影响。
The system consists of initial parameter and cutting depth input, cutting force and cutting power calculation, design result output.
该系统由原始参数、切削用量输入模块、动力参数计算模块、设计结果输出模块等几个主要模块组成。
Factors like internode, node, cutting thickness, moisture content, cutting speed could influence the cutting force in varying degree.
竹材的节间、节部、切削厚度、含水率及切削速度等因素对切削阻力均有不同程度的影响。
The problem that the cutting force is hard to determine in high-speed milling process is solved by using the computer-aided engineering.
用计算机辅助工程的方法解决了高速铣削过程中切削力难以确定的问题。
After analyzing the effect factors of the cutting force in peripheral milling, the paper establishes a steady cutting force allowance model.
并在分析了周铣加工中切削力影响因素的基础上，建立了针对周铣加工的等切削力余量模型。
The minimum cutting force appears in a cutting speed range, the cutting speed is better in this range for the cutting performance improvement.
在较高切削速度时，存在一段使切削力最小的范围，切削时切削速度应尽量选在这段范围内，改善切削效果。
Based on traditional cutting force model in face milling, a new cutting force model for the prediction of static cutting forces has been presented.
以传统的端铣切削力模型为基础，提出了一种新的端铣加工中静态切削力的预报模型。
According to the result of right Angle free cutting experiment, the mathematical model of the cutting force for the arc-edge insert is established.
根据直角自由切削的试验结果，建立了圆弧刃刀片切削力数学模型，同时编制了软件进行预测。
Precision measurement for cutting force plays an important role in the machining accuracy and efficiency of the numerically controlled machine tools.
在数控加工中，切削力的大小直接影响着数控机床的加工精度与效率，因此对切削力的准确测量非常重要。
For the disc shear blade breakdown problem, the idea of reducing cutting force bearing and reasonable allocation of blade cutting force are proposed.
针对圆盘剪剪刃崩豁问题，提出减小剪切受力和合理分配上下剪刃剪切受力的思路。
The research results show that the average axial cutting force and torque of common drill-grinding are greater than that of ultrasonic drill-grinding.
得出普通钻磨时的轴向平均切削力和平均扭矩均远大于超声钻磨加工时的轴向平均切削力和平均扭矩；
The influences of cutting parameters on cutting force and its fractal dimension, surface roughness on the fractal Theory during glass cutting is presented.
基于分形理论研究了玻璃切削时不同切削参数对切削力及其分形维数以及表面粗糙度的影响。
Considering the features of multi-edges and helix flutes for end milling, a cutting force discrete model base on single point cutting tools model was built.
根据单点切削力模型，考虑平头立铣刀多刃和具有螺旋角的特点，建立了铣削力离散模型。
Compared with the cutting force theory formulae before, the cutting force value calculated by the method is more coincident with the practical measuring value.
与以往的切削力理论公式相比，用该方法计算出的切削力值更接近于实测值。
Therefore, cutting force and narrow small incision, cut off, less waste material advantages, such as the new technology is energy-saving cutting, new equipment.
因此，有切割时动力小，切口窄，切面平整，材料损耗少等一系列优点，是节能切割的新工艺，新设备。
Based on the analysis of cutting regimes' influences on milling force, the spectrum analysis and wavelet analysis are applied on the random cutting force signals.
在分析其切削力显著性影响因素的基础上，对切削力随机信号进行了现代谱分析与小波分析。
On the basis of cutting force model and vibration model of machine tools structure, the effect of the regenerative chatter on the stability of end milling is focused.
存得到切削力模型和机床结构振动模型的基础上，着重研究了再生型颤振对铣削加工过程稳定性的影响。
The cutters used in high speed machining(HSM) have poor rigidity, therefore the method fits to HSM of die cavity due to the unfluctuating cutting force characteristic.
其切削力平稳的特性更适合于模具型腔的高速数控加工，可以克服高速加工用刀具刚性差的不足。
Using VC as a design platform, a real-time detecting and compensation system for tool wear based the analyzing and disposing for signals of cutting force is introduced.
介绍了以VC为平台设计开发的一套基于切削力信号分析与处理的刀具磨损实时监测和补偿系统。
The comparison between cutting force results from this model and that from the experiment validates the veracity and practicability of the cutting force model established.
通过与试验结果的对比，本文所建立的高速铣削切削力解析模型对切削过程中切削力的变化趋势预测较为准确；
This paper mainly study the feature of sawing force under stress field. The experiments prove that the cutting force under stress field is smaller than that of common sawing.
本文主要研究了应力场下锯切切削力的特点。试验证明在拉应力场下锯切工件比普通锯切工件的锯切力小，使切削更加有利、高效。
应用推荐