The simulation results verify the high precision of the proposed compensation method regardless of the waveform of ct primary current, remanent flux level, and load characteristic.
仿真结果验证了所提补偿方法的高精度，而且不受CT负载特性、CT剩磁情况及原边电流直流成分的影响。
Based on the analysis of current NC automatic programming systems, a new method for the path control of five-axis linkage machine tools was proposed by means of simulation.
在分析了目前的数控加工自动编程系统后，提出了一种以仿真实现五轴联动机床轨迹控制的新方法。
The paper introduces finite element simulation technology for cover panel stamping forming process, including applied method and software, as well as current status and development trend.
介绍了覆盖件板料冲压成形过程有限元模拟技术的一般方法、常用软件及其最新进展和发展趋势。
Computer simulation results show that the fuzzy PID gain setting control method is superior to current PID control, and greatly improves the dynamic capability and stabilization capability.
通过计算机仿真结果表明，这种模糊增益调整PID控制器比常规pid控制器有更好的控制效果，大大改善了系统的动态和稳态性能。
Simulation results show that the method can realize VC routing effectively according to the current traffic states in the networks and the user-specified delay requirements.
实验表明，该方法可以根据网络当前的业务情况，以及用户提出的时延要求，有效地实现VC路由选择。
The simulation results show that the power factor approaches to 1 (0.99) at stable state, and the exciting current control method and switches table in four quadrants are correct.
仿真结果表明在稳态时功率因数接近于1（0.99），验证了给出的励磁电流的控制方法、四象限开关表的正确性。
Using this method, the minimum switching losses can be reached, and the maximum switching current can be reduced effectively. This has been shown in the simulation results.
这种方法开关损耗最小，并可有效降低开关器件的最大开关电流，仿真结果证明了其可行性。
The electromagnetic force acting on the crack in a metal is studied by numerical simulation method. The distributions of electric current, magnetic field and the electromagnetic stress are given.
用数值模拟方法研究了金属裂纹尖端电磁应力的分布情况，给出了电流分布、磁场分布和电磁应力的分布。
The simulation modeling method of excitation system for stability calculation and the check method of parameters are proposed based on the current need of power system.
结合当前电力系统的实际需要，提出了稳定计算用励磁系统数学模型仿真建模及参数校核方法。
In this paper, based on the related research literature, after anglicizing a variety of inverter current control methods, some research and simulation were done on hysterics current control method.
本文在调研相关文献的基础上，分析了各种逆变器电流控制方法，并且对滞环电流控制方法进行了研究和仿真。
Second, analyzes the pulsed eddy current impedance model in detail, improves simulation of pulsed eddy current method of calculating, and carries out thickness, ranging simulation.
其次，详细分析脉冲涡流检测的阻抗模型，改进了脉冲涡流仿真计算方法，并进行了测厚、测距的仿真实验；
The simulation tests show that the new method can correctly judge the transformer's inrush current and internal fault without the harmonic effect, and it has a good reliability.
经仿真实验表明：该方案能准确地判别出变压器内部故障和励磁涌流，不受系统谐波影响，具有很高的可靠性。
The results from calculation and simulation show that the proposed method can effectively restrain the negative sequence voltage and current caused by unbalanced parameters of transmission line.
计算分析结果表明，该方法能够有效抑制由线路参数不对称产生的负序电流和电压。
The results of the digital simulation show that the method can identify fault current and energizing inrush current precisely and makes it rapid and reliable for the protective relay to …
数字仿真结果表明，本方法可准确识别故障电流和励磁涌流，即使在空载合闸于内部故障时，保护继电器也能迅速可靠动作，避免了采用二次谐波制动导致的误动问题。
To solve this problem, current paper presents a different method and calculated damper structure parameters from computer simulation match experiment results quite well.
针对该计算方法存在的问题，提出了不同的计算方法，并用计算机程序计算，得出的防振锤结构参数比较接近实际试验结果。
By means of circuit topology theory and loop current method, simulation and calculation are performed on the 12-phase power winding of an induction generator with rectifier load system.
为了对异步发电机十二相功率绕组带整流负载系统进行仿真计算，采用了基于电路拓扑理论的回路电流法。
Current distribution in three-phase cylindrical buses is calculated through simulation current method and magnetic field surrounding the buses can be calculated too after that.
为了研究建筑物配电房母线产生的工频磁场，根据配电房大电流母线集肤效应显著的特点，提出了采用模拟电流法对三相母线的矢量磁位进行计算。
The mechanism of current-unbalance of 1/2-level is analyzed in detail by simulation. By using current-feedback control, a new PWM control method with the capability of current-balance is proposed.
结合仿真，详细分析了产生1/2电平电流不均衡的机理，并提出了一种通过直流侧电流反馈来实现均流调节的脉宽调制（PWM）控制方法。
The mechanism of current-unbalance of 1/2-level is analyzed in detail by simulation. By using current-feedback control, a new PWM control method with the capability of current-balance is proposed.
结合仿真，详细分析了产生1/2电平电流不均衡的机理，并提出了一种通过直流侧电流反馈来实现均流调节的脉宽调制（PWM）控制方法。
应用推荐