The torsion resistance of the tension bar and the calculatiolls of bending shear stress, free torsional shearstress and bending torsional shear stress on the section are also discussed.
性质:用圆柱形材料试件作抗扭实验可求得扭矩和扭角的关系,相应最大扭矩的最大剪断应力叫抗扭强度。
The mechanical behavior of steel webs with negative bending was studied with combined stress loads of flexure, axial pressure and shear to prevent local buckling in continuous composite beams.
为避免钢混凝土连续组合梁发生局部失稳,对负弯区钢梁腹板在弯曲应力、轴向压应力和剪应力联合作用下的力学性能进行了研究。
The bending and shear modifying coefficients are derived according to the distribution of the stress and strain of the sandwich plate along the direction of the plate thickness.
根据夹层板的正应力、正应变和剪应力、剪应变沿板厚的分布关系,得到夹层板的弯曲、剪切修正系数。
This paper shows that the shear stress distribution in bending layer has similar characteristics as the strain distribution near the ends of the actuator.
通过分析可得,粘贴层剪切应力的分布与致动器端部附近的应变分布有相似的特征。
The interfacial shear stress and peel stress between the FRP and the surface of tension flange were analyzed when the FRP was bonded to the tension flange of the bending members.
对受弯构件受拉翼缘外侧粘贴FRP后的界面剪应力和界面剥离应力进行了分析。
The effects of the nonuniformity of porosity development and stress distribution on material bifurcations(plane shear bending and surface wrinkling)are investigated by means of numerical method.
利用数值方法研究材料空洞化和承受应力沿板厚分布的非均匀性对材料分叉(平板中平面剪切带和表面皱曲)的作用。
The influences of moving load on shear stress and bending moment are analysed by static characteristics, and the reliability of crane is studied with MonteCarlo method.
通过静态特性研究,分析了移动荷载对结构的剪力、弯矩和应力的影响,分别确定了剪力值最大、弯矩值最大和应力最大的位置。
In this article, it shows formulas to calculate bending moment, shear strength and maximum stress of heat tracing pipe and shell body.
首先给出了半管加热管及壳体的弯距、剪力及最大应力计算公式。
A complete set of equations for cable dynamics is put forward by using some tensor relations, in which the effects of shear stress and bending moment are included.
利用张量关系,推导了完整的缆索动力学方程组,包含了剪切和力矩的影响,并把它们表示在两种不同的常用坐标系中,以便查阅。
Secondly, the paper analyze the interfacial shear stress distribution rule through setting up and analyzing finite element models of RC beams in bending or in shear strengthened with CFS;
通过建立碳纤维布加固受弯梁的有限元分析模型,对基于受弯和受剪加固的粘结剪应力进行了分析;
Secondly, the paper analyze the interfacial shear stress distribution rule through setting up and analyzing finite element models of RC beams in bending or in shear strengthened with CFS;
通过建立碳纤维布加固受弯梁的有限元分析模型,对基于受弯和受剪加固的粘结剪应力进行了分析;
应用推荐