检查锚机及绞车的各轴承间隙。
本文主要叙述发电机筒式导轴承间隙对机组安全运行的影响。
This paper mainly describes the influence of generator barrel bearing on the operating safety of the units.
滑动轴承间隙要按高精度设计、制造,才能保证设备的可靠性。
The sleeve bearing must be designed and made with close to tolerance to provide the equipment high reliability.
如果材料模量与轴承间隙越小,轴承厚度越厚,则压力分布越均匀。
Smaller both the material's elastic modulus and clearance, and thicker thickness, more even pressure distribution is.
由于工程陶瓷很脆且膨胀系数小,所以轴承间隙不得过小,以免发生抱轴事故。
As the project is very brittle ceramic expansion coefficient and small, bearing gap may not be too small to hold axis in order to avoid accidents.
轴承间隙后,不仅成品轴承支撑的资格认可的主要参数之一组件,而且还可以承载的一个重要因素。
Bearing clearance, not only finished products bearing support of one of the main parameters of accreditation component, but also carry an important factor.
首先对噪声信号进行小波包分解,得到含有待诊断柴油机主轴承间隙故障信息的噪声信号时频分布图,并由此定义图像。
We illustrate the wavelet package analysis that can obtain the time-frequency distribution figure of noise signal, which can be used to define gray-image.
舵轴承安装间隙测量。
本文提出使用8098单片机实现轴承轴向间隙检测的新方法。
This paper presents a new method for detecting the axial clearance of a bearing by a single chip processor 8098.
艉轴承弹性模量、径向间隙、厚度对接触压力分布有明显的影响。
The contacting pressure of the stern bearing is influenced with its elastic modulus, radial clearance and thickness.
第二种适用于特殊全封闭的轴承,其一头有间隙并有定位螺丝孔。
The second applies to a special closed-wide bearings, which have a gap and a positioning screw holes.
通过实例介绍了滑动轴承径向间隙理论值和实际值的确定。
To determine the theoretical value and practical value of radial clearance of sliding bearing was introduced with practical example.
轴承在工作中,由于外界或内在因素的影响,使原有配合间隙改变,精度降低,乃至造成“咬死”称为游隙变化失效。
Bearing in the work, because of external or internal factors, with the gap so that the original change, lowering the precision, and even lead to "killed" clearance changes as failure.
通过对汽封轴封间隙和轴系联轴器中心的调整,避免了机组冷态启动时汽封、轴封部分径向的动静碰磨,从而明显降低了轴承的振动。
Bearing vibration during cold starting has now been remarkably mitigated by readjusting gland clearances and coupling alignment, herewith preventing the occurrence of radial gland rubbing.
轴承一般设一个小轴向间隙,以弥补轴和轴承座的长度变化。
The bearings are generally installed with a small axial clearance in order to compensate for length variations of shaft and housing.
同样,在进行曲轴轴颈和曲轴轴承配合间隙的测量时,也可以借鉴这种操作技巧。
Similarly, in the crankshaft journal and crankshaft bearing clearance measurements, they can draw on such skills.
最简单的结构形式是在轴和轴承盖的通孔之间留出半径间隙约为0.1~0.3mm的隙缝。
The structure of the simplest form of shaft and bearing caps in the through-hole gap between the left radius of about 0.1 ~ 0.3mm gaps.
当轴承配套的主要质量指标之一径向间隙。
When the bearings supporting the main indicator of the quality of radial clearance.
轴承表中给定的速度评级值适用于单一的安装,轻轻预装nke的主轴轴承(即零间隙操作)。
The values of speed ratings given in the bearing tables apply to single mounted, lightly preloaded NKE spindle bearings (ie operating at zero clearance).
数值结果表明,同轴承长径比及转子质量偏心相比,轴颈间隙是影响系统轴心轨迹和频域特性的主要因素。
The result shows that compared with slenderness ratio of bearing and the eccentricity of rotor, the journal clearance is the main factor influencing the trajectory and domain characteristics.
解决刀片回转不均匀问题的关键在于优化设计刀片回转轴与轴承、刀片内孔之间的配合间隙。
The key to solve the problem lies in the optimal design of clearances between the insert rotary shaft and its bearing as well as the round insert fitted hole.
工作台主轴采用高精度可调径向间隙双列短圆柱滚子轴承定心。
Work spindle with high precision adjustable radial clearance of double row cylindrical roller bearing centering.
本文介绍模拟试验中轴承表面光洁度和配合间隙与磨损的关系,同时简述了磨损试验和测量方法。
This paper investigates the influence of bearing's surface finish and clearance on its wearability obtained by simulating tests. The method of the wear test and measurement are briefly described.
作战间隙,无内圈滚针轴承组件,它运行到轴上直接决定选定一个“实际”的滚道的公差范围。
The operational clearance for needle roller bearing assemblies, without inner rings, which run directly onto the shaft is determined by the tolerance field selected for an "actual" raceway.
通过调整对另一轴承,圆锥滚子轴承的轴向间隙控制在安装。
The axial play of taper roller bearings is controlled during mounting by adjusting one bearing against another.
有源静电悬浮轴承通过检测电极与转子间构成的球面间隙电容以得到转子位移。
The rotor motion in an active electrostatic bearing is obtained by detecting the variation of the spherical capacitance between electrodes and the rotor.
运用此方法对内燃机主轴承不同间隙下的噪声信号进行分析,结果表明,此方法能有效地提取故障的特征,实现状态监测。
Applying the order bi-spectrum in the analysis of engine noise signals shows that it can extract the fault characteristics and realize the state monitoring.
整体轴承箱第二大优势就是,只需转动轴承箱即可实现间隙的调整。
Whole bearing box's second biggest advantage is, need to turn the bearing box clearance adjustment can be realized.
整体轴承箱第二大优势就是,只需转动轴承箱即可实现间隙的调整。
Whole bearing box's second biggest advantage is, need to turn the bearing box clearance adjustment can be realized.
应用推荐