Through test and analysis of working stress on balance beam and lengthwise beam of dozer frame, a strength design method and the basis for compiling load spectrum are given in the paper.
通过对推土机平衡梁和车架纵梁的工作应力测定与分析，掌握了推土机的强度设计方法，为编制载荷谱打下基础。
We think that the method of estimating maximal pre-applied stress of the working bolt can provide a reference for preventing further fatigue fracture of boxter bolts.
认为用估算螺栓工作时的最大预紧应力的方法，对防止埋头螺栓疲劳断裂再次重复发生有一定的参考价值。
By means of the method of finite element analysis, and simulating the actual working status of the press, the stress and deformation value of each hinge beam part of the press were obtained.
借助有限元分析方法，模拟压机的实际工作状态，获得了压机铰链梁各零件的应力和变形值。
It was very complicated when taking the traditional equivalent section method to calculate the section stress of steel concrete structural unit under its normal working condition.
对于钢筋混凝土构件在正常使用状态下的截面应力计算，用传统的“等效截面法”计算十分复杂。
Analyzing the stability of the side slope through classical ultimate balance method, the working state is fictitious without considering the stress-strain relation of the soil mass.
采用传统的极限平衡方法来分析边坡的稳定，没有考虑土体本身的应力—应变关系，其工作状态是虚拟的。
Lastly, using fatigue reliability design method, this paper analyses the crane wheel according to the probability distribution of its working stress and fatigue strength.
最后，根据起重机车轮的工作应力和疲劳强度的概率分布，采用疲劳可靠性设计方法，对车轮进行了分析计算。
On the basis of finite element analysis, 5 concrete columns were made to carry on the experimental study about the measurement of working stress of concrete by the ring-hole method.
本文是在有限元模拟分析基础上，制作5根混凝土柱，进行环孔法测试混凝土工作应力的试验研究。
Test results show that the method can simulate turbine blade key section "s working" stress field "and temperature in the laboratory and give reasonable life data for turbine blade."
试验结果表明：试验方法能够模拟涡轮叶片考核截面在实际工作状态下的应力场和温度，利用所提出的试验方法和分析技术得到叶片的寿命数据是合理的。
The method of measurement of resistantence strain working as a method of measuring stress was widely applied to the stress measurement of each point in pressure container.
电测法作为一种实验测定应力方法，普遍用于压力容器各点处的压力测定。
This paper proposes a method to calculate the transient temperature field and stress field of a working brake disc with 3 dimensional cycle symmetric model.
提出了一种以三维循环对称有限元模型计算制动过程中制动盘温度场和应力场的方法。
The cage mechanical model build by force method after compares several calculation methods. Introduced the stress and calculation process of cage in three working conditions detailed.
在综合比较各种计算方法的优缺点之后，采用力法建立了罐笼的力学模型，并系统分析了罐笼在三种工况下的受力情况，给出了详细的计算过程。
The cage mechanical model build by force method after compares several calculation methods. Introduced the stress and calculation process of cage in three working conditions detailed.
在综合比较各种计算方法的优缺点之后，采用力法建立了罐笼的力学模型，并系统分析了罐笼在三种工况下的受力情况，给出了详细的计算过程。
应用推荐