Tapping: refers to the workpiece within the processing of a thread process.
攻牙:指在工件上加工出内螺纹的工艺过程。
Impact tapping, as a novel technology of internal thread processing, has some important effect and a good applied foreground in the machining of small diameter thread, especially for thin board.
冲击攻丝作为一种新型的内螺纹加工技术,在解决小直径薄板内螺纹加工方面发挥着重要的作用,并具有良好的应用前景。
Conductive thread of a hole without cutting tapping new technology to solve the past conductive thread easily slip teeth of the defects.
导电件螺纹孔采用无切削攻丝新工艺,解决了已往导电件螺纹容易滑牙的缺陷。
In addition, they believe, for tapping there exists a critical cutting thickness (thread depth) value of the critical cutting thickness within the tapping can reduce the tapping torque.
此外,他们认为,对于攻丝存在一个临界切削厚度(螺纹深度)值,在临界切削厚度的范围内,攻丝能降低攻丝扭矩。
When tapping the little diameter in the material of difficult processing, there usually exist a lot of questions such as tapping torsion heavy, thread accuracy low, rejecting rate high.
在加工中小直径内螺纹和在难加工材料上攻丝时,普遍存在攻丝扭矩大、螺纹精度低、丝锥易折断、废品率高等问题,而采用低频振动攻丝是解决此问题行之有效的方法。
With cars, milling, boring, drilling four automation function, can be turning sphere, cylinder, cone, thread, tapping, end face, inner and outer ring groove, etc.
具有车、铣、镗、钻四大自动化功能,可车削球面、柱面、锥面、螺纹、攻丝、端面、内外环槽等。
Those traditional method are confronted with several problems: having difficulty with conquering dynamic load in tapping and leading to thread breaking, block, abrasion and low machining quality.
这些传统加工方法存在的问题有:难以克服攻丝过程中的动态载荷,导致丝锥折断、阻塞、磨损等,同时加工质量不高。
The microstructure of the thread machined by form tapping showed a layer of fine fiber distribution along the thread profile.
加工的挤压螺纹表面有一层纤维沿其牙形连续分布。
Based on the analysis of tapping force system and characteristic of chip removal, it is confirmed that radial force, axial force and jam of chip removal are the main reasons for poor thread quality.
通过对攻丝切削力和丝锥排屑特点的分析,确定径向力、轴向力和排屑不畅是影响攻丝质量的主要因素。
During tapping in steel crankshafts, the most commonly encountered problems are "mess tooth" and oversize thread, additionally the tap life is very low.
前言:钢质曲轴螺孔攻丝加工中经常出现螺纹烂牙、中径扩大等问题,且刀具寿命较短。
The thread of any shell tapping shall be selected from and be in accordance with Table5.
任何筒形丝锥的螺纹应该从表5中选择,且符合表5的要求。
Cold form tapping process is an effective method to enhance fatigue strength of internal thread.
内螺纹冷挤压成形是提高内螺纹疲劳强度的有效方法。
Tapping is a wide method of processing interior thread.
攻丝是切削加工中广泛使用的一种内螺纹加工方法。
Tap limit does not guarantee thread limit for the internal thread after tapping.
丝锥精度不能够保证内螺纹的精度。
The company is a manufacturer specialized in producing M1.4-M6 screws, tapping screws and three-edge thread forming screws according with the standard of JIS, GB, ANSI and DIN.
我司主要生产M1.4-M6系列机螺钉、 自攻螺钉及三棱自攻锁紧螺钉,产品执行JIS标准、GB标准、ANSI标准、DIN标准,原材料选用优质的碳素钢、铜及不锈钢等。
Tapping is the process of cutting a thread inside a hole so that a cap screw or bolt may be threaded into it.
攻丝是在一个孔中车出螺纹,以便装上有帽螺钉或螺栓。
We possess about 119 Presses of different tonnages, Cutting Machines, Multi Spot Welding Machines and Welding Robot Systems, Tapping Machines, Thread Rolling Machines, CNC and others.
公司有各种吨位的压机119台,此外还有各类剪板机、储能焊机、自动机械手设备及螺纹攻丝、滚丝设备以及数台数控机床、加工中心等。
We possess about 119 Presses of different tonnages, Cutting Machines, Multi Spot Welding Machines and Welding Robot Systems, Tapping Machines, Thread Rolling Machines, CNC and others.
公司有各种吨位的压机119台,此外还有各类剪板机、储能焊机、自动机械手设备及螺纹攻丝、滚丝设备以及数台数控机床、加工中心等。
应用推荐