In the left paper, essential technology of software and hardware design scheme, systematic simulation is expounded, the DSP and FPGA is selected as the core of system hardware platform.
论文后半部分详述了该定位系统样机在实现过程中的软、硬件设计方案及系统级试验的关键技术。
According to simulation model, the effect of backlash and dead zone nonlinear factors on systematic performances was analyzed, and the measures of improving the systematic performances were given.
利用仿真模型分析了间隙、死区等非线性因素对系统精度的影响，并给出了提高传动系统性能的措施。
Simulation results show that the systematic precision of position and speed has quite remarkable improvement in case of integrated discontinuity at short intervals.
仿真结果表明：在组合中断时间较短的情况下，系统的位置、速度精度均有相当显著的提高。
Modeling the systematic components of different variation sources and implementing these effects in circuit simulation are key to reduce design uncertainty and maximize circuit performance.
在电路仿真时对不同变化源的系统部分建模和分析成为减少设计不确定和最大化电路性能的关键。
The optimal integration and simulation of heat transfer network is the most active area in the study of systematic engineering of heat utilization.
热量传递网络的优化综合与模拟，一直是热量利用系统工程的最活跃的研究领域。
Combining the practice from technology development of a propylene oxide project, systematic introduction is given to two technologies of simulation enlargement and stream heat recuperation.
结合环氧丙烷项目工艺技术开发的实践，对模拟放大和物流余热利用两项技术做了系统介绍。
Based on systematic analysis of integrated disease management system of rubber powdery mildew, a control decision model was established by using computer simulation.
根据综合治理系统的系统分析，用电算模拟的方法建立了橡胶白粉病防治决策模拟模型。
Introducing systematic dynamics and nonlinear economic approaches, this paper establishes the theoretical model based on the simulation research on a vast amount of data.
利用系统动力学和非线性经济计量方法，以各样本国数据资料进行模拟研究，建立理论模型。
The simulation calculation of radar systematic error shows that the results are satisfactory and better than those of principal component estimate.
干涉仪雷达系统性误差的模拟计算表明：效果良好，优于主成分估计。
This thesis is on the basis of the research of diesel engine type 4135 etc, and the complete and systematic numerical modeling and malfunction simulation for thermal loading.
本文以4135柴油机等机型作为研究对象，对其热负荷进行了全面系统的数值模拟和故障仿真。
Most of power system's simulation tools have not the systematic model of relay system and can not response the control rules of relay system truly and completely.
目前大多数电力系统仿真分析工具缺少对继电保护模型的系统化描述，无法真实完全的反映继电保护元件的控制规律。
A systematic evaluation of source rock from central Tarim basin is provided and the scale of oil and gas generated from source rock in the area is calculated with the method of basin simulation.
系统评价了塔里木盆地塔中地区的烃源岩，采用盆地数值模拟方法定量计算了塔中地区的生、排烃数量。
New systematic approach to the simulation of circuits containing ideal operationamplifiers using the standard simulators such as PSPICE is first presented.
本文提出了一种完全依照理想运算放大器的特性，对含这类元件的线性时不变电路利用PSPICE进行计算机仿真的新方法。
A method was proposed to put up the visual simulation and test platform for subway on-board system, and the systematic framework and detailed design of platform were provided.
提出了一种为地铁车载系统搭建可视化仿真测试平台的方法，给出了详细的系统架构和设计方法。
Through systematic analysis of ANSYS modelling and meshing module, incorporation roadway design experience, a simulation calculation method on U29-type steel flexible support was found out.
通过对ANSYS模型建立和网格划分模块的系统分析，结合巷道支护经验，找出了对U 29型钢可缩性支架进行模拟计算的方法。
The paper presents a systematic technology of feed rate optimization on CNC planar profile milling based on geometric simulation of tool path which is the base of intelligent CNC programming.
本文基于刀具路径几何仿真，研究了平面曲线轮廓数控加工进给速度优化技术，这种优化技术是智能化数控加工编程的基础。
Through the systematic analysis of ring anode baking process, a mathematical model was developed. Several simulation runs were then made.
通过对环式阳极焙烧炉的热工过程进行系统理论分析，建立了焙烧炉热工过程的数学模型。
A systematic and concise description has been given to its physical feature, basic assumptions and theoretical simulation procedures.
文中系统而简要地阐述了它的物理图象、基本假设和计算公式。
This paper gives a systematic analysis on the motion simulation content,...
本文系统的分析了运动模拟的内容、求解方法和实施步骤。
Systematic Dynamic Characteristic Digital Simulation of Computer Control System in CNC Machine Tools;
宝钢分公司多条冷轧生产线的过程控制计算机使用了日立控制系统。
Systematic Dynamic Characteristic Digital Simulation of Computer Control System in CNC Machine Tools;
宝钢分公司多条冷轧生产线的过程控制计算机使用了日立控制系统。
应用推荐