System Processors Memory Disk Swap partition network.
系统处理器内存硬盘交换分区网络。
This tells you that you have one swap partition defined.
这说明已经定义了一个交换分区。
That location could be physical RAM, a file, or the swap partition.
该位置可以是物理ram、文件或交换区。
Swap space in a file rather than a dedicated swap partition is another example.
文件中的交换空间（不是专用交换空间）是另一个示例。
The required partitions are the PReP partition, swap partition, and a root ("/") partition.
所需的分区包括PReP分区、swap 分区和一个根分区 ("/")。
Also remember to set the "partition Type" to "Linux swap" when creating your swap partition.
还要记住在创建交换分区时，将“PartitionType”设置为“LinuxSwap”。
It creates an image which is saved in an active swap partition selected by kernel option.
它创建一个保存在由内核选项选择的活动交换区中的镜像。
The steps above can also be used to add more swap space to a system that has an existing swap partition.
这些步骤同样可以用来增加现有扩展分区的大小。
It is much better to place swap partition as close as possible to the partition where the OS is installed.
将交换分区分配在操作系统所装的分区的相邻为止会更好。
To delete additional swap, you can use the corresponding swapoff or swap -d command to disable the swap partition.
若要删除额外的交换空间，您可以使用对应的swapoff或swap- d命令来禁用该交换分区。
However, note that you can only disable swap that is not currently in use, and it is not possible to disable the primary swap partition.
然而要注意，您只能禁用当前未使用的交换分区，并且不能禁用主交换分区。
Attaching a higher priority to the SSD swap allows it to be used until exhausted; only then would pages be written to the lower-priority (slower) swap partition.
为ssd交换附加一个更高的优先级使其可以使用直至耗尽；直到那时，页面才能被写入优先级较低的交换分区。
Note that the extended partition is locked in this way if any of its contained logical partitions are in use, including swap space.
注意如果扩展分区其中包含的任何一个分区(包括交换空间)正在使用，那么它是以这种方式锁定的。
If you don't have a spare partition available, then you can create one or more files, which you can temporarily add into the available swap pool.
如果没有空余的分区可用，您可以创建一个或多个文件，并将它们临时添加到可用交换池中。
Swap space is located in the first IDE hard drive in the sixth partition, the second logical drive in an extended partition.
交换分区位于第一个IDE硬盘驱动器的第六个分区，也就是扩展分区的第二个逻辑驱动器。
You should configure a dedicated partition for swap space as soon as possible.
您应该尽快为交换空间配置专用分区。
Each disk holds a primary ext3 partition and a 500mb swap and a ~ 2gb ext3 partition inside the Extended volume.
每块磁盘有主要的ext 3分区和500MB的交换区和扩展卷中的2gb的ext3分区。
Specify the type of partition: ext2, ext3, vfat, swap, or prep.
指定分区的类型：ext2、ext3、vfat、swap或prep。
The rule of thumb is that you choose between 1.5 to 2 times the amount of RAM as the swap space, and you put this partition in a place that is quick to reach, like at the beginning or end of the disk.
swap分区大小的原则是根据你的内存大小而设置，一般就是内存的1.5到2倍大。而且最好把swap分区放在硬盘的最前面或者最后面以便读写。
A smaller partition used to augment your RAM, mounted and referred to as swap.
一个比较小的分区用来扩大内存，挂载为swap。
If you have a partition available, then you should prepare it as outlined above in the Configuring swap space section.
如果有某个分区可用，您可以按照上面在配置交换分区部分中的介绍来准备它。
What you need at the least is one primary partition which contains the root and one for swap.
至少需要有一个包含了根的主分区和一个交换分区。
What you need at the least is one primary partition which contains the root and one for swap.
至少需要有一个包含了根的主分区和一个交换分区。
应用推荐