This article introduces the principles, structure, characteristic index and features of compound propulsive steering controller.
文章介绍了复合式推进操纵控制器的原理、结构、性能指标和特点。
The necessary shifts in signal phase are controlled via a dedicated beam steering controller or the architecture's central processor.
信号相位的必要相移通过专用波束调节控制器或集中安排的处理器进行控制。
This paper analyses the reason for the loss of stabilization for vehicle steering controller at low speed based on two degree freedom dynamic.
本文从理论上分析了基于车辆二自由度转向动力学模型的转向控制器在低速时产生失稳的原因。
Secondly, the mining vehicle's kinematic model is deduced as driving on the slope. Finally, the optimal steering controller is designed as a key determinant of the turning control system.
通过分析转向过程中采矿车与海底底质的作用力关系，建立了采矿车在海底斜坡转向的运动学模型，设计了以最优控制器为核心的转向控制系统。
A fuzzy controller for ship steering based on RBF networks and genetic algorithms is designed.
设计了一种基于RBF网络和遗传优化的船舶操纵模糊控制器。
The simulation results show that the strategy is more effective in improving the performance of power steering and robustness than the conventional PD controller.
仿真结果表明，基于模糊pd控制的电动助力转向系统比传统PD控制具有更好的助力特性和抗干扰能力。
For this design the steering behaviour of a human controller is transformed into a fuzzy 'mathematical model.
这种设计是将人工控制的操纵行为翻译成一个模糊数学模型。
The local controller sends steering order to field signal-acquisition equipments and receives test data from RS485 bus, thereby communication control of RS485 bus was realized.
本地主控机通过RS485总线向现场信号采集设备发送控制指令并接收采集的测试数据，从而实现对rs485总线通信的控制。
A fuzzy adaptive PID controller was proposed to be used in a four wheel steering platform.
针对机-电-液复合结构的四轮转向平台具有非线性、快时变的特点，提出了模糊自适应PID控制策略。
The results of simulation and test prove that the math mode is correct and effective, and the controller is suitable for improving the dynamic performance of the electric power steering.
仿真和试验的结果均表明所建模型是正确和有效的，采用的控制方法对提高汽车转向的动态特性有显著作用。
According to the coupling relationships among steering, suspension and braking systems, a central controller is designed for conducting coordinated control over subsystems.
根据转向，悬架和制动系统的耦合之间的关系，一个中央控制器的设计进行协调控制子系统。
A propulsion controller, a swing controller and a steering control board constitute an electric propulsion control device.
推进控制器、回转控制器和驾驶操纵台组成了电力推进控制装置。
This paper mainly describes the composition of beam-steering system and the design of sub-array controller in beam-steering system.
本文主要论述了波控系统的设计及其中子阵波控模块的实现方法。
The central controller (3) is connected with the steering valve (7), the pressure sensor (2), and the roller rolling pump (4) via control lines (10).
中央控制器(3)与换向阀(7)、压力传感器(2)、滚柱滚压泵(4)分别有控制线(10)连接。
The central controller (3) is connected with the steering valve (7), the pressure sensor (2), and the roller rolling pump (4) via control lines (10).
中央控制器(3)与换向阀(7)、压力传感器(2)、滚柱滚压泵(4)分别有控制线(10)连接。
应用推荐