This paper introduces the hardware and the software of microcomputer control system for sign typewriter on the railway vehicle bearing.
本文介绍铁道车辆轴承标牌打字机的微机控制系统的硬件结构和软件特点。
This paper developed a practical system software of microcomputer numerical control system based on the analysis of the hardware construction and principle of the AC servo X - Y table.
本文针对微机数控交流伺服X-Y工作台的硬件结构以及其工作机理，介绍了一套可实际应用的微机数控交流伺服系统软件的开发。
The article can also be the reference for software programming of microcomputer interlocking station (with track cut point signal).
也可作为微机联锁车站(亦有股道分割点信号机)软件编程时参考。
The paper presents the control strategy of the microcomputer with knowledge base, and describes the software and block diagram of work of the two-stage microcomputer control system.
本文给出了带知识库的微型计算机控制策略，介绍了两级微机控制系统的软件和工作框图。
The apparatus consists of a single board microcomputer, propeller type velocity sensor, tail fin type flow direction sensor and corresponding interface circuits and software.
该仪器以单极微机为核心，配置旋浆流速传感器、尾舵式流向传感器、相应的接口电路和软件。
The practices prove that the antijamming measures of the software combined with the hardware ensure the microcomputer system for reliable run in the welding industrial circumstances.
实践证明，软、硬件相结合的抗干扰措施保证了微机系统在焊接工业环境中的可靠运行。
This is the principle of microcomputer software.
这是微机原理有关的软件。
Based on the analysis of the theory of vulcanization, the control of rubber vulcanization, the construction of microcomputer control system, hardware and software design were described.
在分析橡胶硫化机理的基础上，阐述了胶料硫化的控制方法、微机控制系统的组成、硬件配置和软件设计。
The Micro professor single board Microcomputer implements performance of logic control using software structure.
小教授单板机是利用软件设备来完成逻辑控制的功能。
This paper introduces the application of the method of object oriented analysis and design in software system of new-style microcomputer nuclear gauge and control system, which we developed recently.
介绍了面向对象的分析、设计方法在最新研制的新型微机核子秤计量与控制系统的软件系统中的应用及其具体实现。
In this paper, the hardware, software, control schemes and control algorithm of the microcomputer supervising control system are introduced on styrene pilot test installation.
本文介绍了苯乙烯小试装置微机监控系统的硬件，软件设计和系统的控制方案及控制算法。
The structure and the principle of auto board shears have been introduced with the design method of hardware and software implemented by 8051 single chip microcomputer.
介绍了自动剪板机系统的结构组成和工作原理，叙述了8051单片微机实现其生产过程控制的硬件与软件的设计方法。
The article has detailed the hardware and software design of this microcomputer control system.
详细介绍了这个微机控制系统的硬件电路及软件设计。
The operational principle and the design of hardware circuit and software of a simple and practical microcomputer interfacing circuit for flow detecting are introduced.
介绍一种简单实用的流量检测微机接口模板的工作原理、硬件电路及软件设计。
The article treats of the software of the dynamic weighbridge with microcomputer.
本文介绍了一种双台面微机动态轨道衡的新型软件。
The developing process of single board microcomputer has been discussed by combining of hardware and software.
对单板机以逐步集成法和硬软件结合的开发过程进行了讨论。
This paper introduces an algorithm of adaptive Kalman filter and its microcomputer software for extracting EEG signal.
本文介绍了一种提取脑电信号的自适应卡尔曼滤波算法及其微机处理软件。
This paper describes a design scheme of the hardware and software, with which the microcomputer controls electronic display consisting of LED point lattice.
本文介绍由发光二极管组成的点阵作电子显示屏，并由微型计算机进行控制的硬件和软件设计方案。
The special microcomputer software for calculation of slot electric field is worked out with fe method, and the field distribution in stator slot winding of large generator is calculated.
采用有限单元法，编制了适用于微机系统的槽部电场计算专用软件，计算了大型发电机定子线圈槽部电场的分布。
Introduces the usage of hardware and software in integrating the supervision alarm and video switch in the 8031 microcomputer using the example of supervision alarm system in Banks.
通过银行监测报警系统这一实例，详细介绍了用8031单片机实现实时监测报警与视频切换于一体的监测系统的硬件及软件设计。
This paper describes the principle, derivation of the engineering formula, software functions and characteristics of a microcomputer controlled dynamic length measuring device for red-hot steel plate.
本文叙述了微机控制的红热钢板动态测长仪的原理、工程公式的导出、软件功能及其特点。
The general drilling depth system is composed of a single-chip microcomputer, a personal computer, hardware and software.
用单片机和微机共同构成的通用钻井深度系统由硬件和软件组成。
The control principle and software of the microcomputer controller used in DC impulse seam welding are introduced in this paper.
本文介绍了直流冲击波缝焊微机控制器的控制原理及软件系统。
The paper analyzes the disturbance sources of microcomputer application system and provides practical and concrete anti-disturbance methods of both software and hardware.
较详细地分析了微机应用系统的干扰源，并结合实际给出了采取软、硬件两种方法抗干扰的具体措施。
In this paper, we introduce the principle of metallographical cutter control system and the design method of software and hardware based on the AT89S52 singal-chip microcomputer.
介绍了以AT 89s52单片机为核心的金相切割机控制系统原理和软硬件设计方法。
The problems of electronic circuit design of pulse power with high voltage, the components of microcomputer control system, and the design of application software are also discussed.
论述了高压脉冲电源电子线路设计、微机调控系统组成及系统应用软件设计与开发问题。
IBM PC and single chip microcomputer communication hardware circuit, software interface and measure to improve reliability of communication.
IBMPC机与单片机通讯的硬件电路、软件接口以及提高通讯可靠性的措施。
This paper introduces interruption system software structure and operation of 32 Bit 80960KB Single-chip microcomputer.
本文主要介绍32位单片机80960KB中断系统的软件结构及其运行机理。
This paper introduces the structure, hardware circuit and software design of PWM DC power amplifier controlled by microcomputer.
本文介绍了单片机控制的PW M直流功率放大器的结构形式、硬件电路以及软件设计。
This article introduces the basic principle of the programme control amplifier controlled by 8031 single chip microcomputer and the design thought of the system hardware and software.
本文介绍了一种由8031单片机系统控制的程控的放大器的基本原理和硬件与软件设计思想。
应用推荐