Rotational molding process provides the product extra strength and sturdy feature.
滚塑工艺成型，产品结构坚固。
And the development of different kinds of plastics for rotational molding especially PE were discussed.
探讨了可用于回转成型的各类塑料，尤其是聚乙烯的研究开发情况。
The development of the plastics for rotational molding rotational molding machines and technics was reviewed.
综述回转成型塑料、设备与工艺的研究进展。
It introduced the processing technology of the product from composite materials by means of rotational molding method.
介绍了利用旋转模塑方法成型复合材料制品工艺。
The article deals with the situation and development tendency of rotational molding of plastics both at home and abroad.
本文简要介绍了目前国内外滚塑工业的现状与发展趋势。
The defects of stamping and plastic-absorbing technology were analyzed, and the principles and merits of rotational molding were introduced.
分析了冲压技术和吸塑技术的缺陷，介绍了滚塑成型的原理和优点。
Rotational molding is good to deal with large and complex tanks. And rotationally molded tanks can be very strong by increasing its wall thickness.
滚塑工艺适合做大型、复杂的水箱或油箱。并且滚塑的水箱或油箱可以通过调整壁厚来增加强度。
The method and application of rotational molding were introduced. The intention and signification of solving defects of rotational molding products were presented.
简要介绍了旋转滚塑成型的方法和用途，指出了研究并解决滚塑制品缺陷的目的和意义。
It was suggested that in the rotational molding, the initial viscosity controlled the wall thickness of the product and the gel rate controlled the uniformity of the wall thickness.
试验表明，树脂体系的初始黏度对制品最终壁厚影响较大，体系的凝胶速率对制品壁厚均匀性影响较大。
Steel, net, plastic 3-1 - will be welded to the steel wire mesh surface to polyethylene as raw material, the use of rotational molding technology, an overall shape in the steel surface.
钢、网、塑3合1——将钢网焊接于钢体表面，以聚乙烯为原料，采用滚塑技术，一次整体成型于钢体表面。
The heating times during the rotational molding of the hollow plastic products were studied according to the theory of heat transfer and interfacial movement, and an algorithm was proposed.
为了解决滚塑成型工艺中加热时间难以确定的问题，依据传热学和界面运动理论进行了滚塑成型加热时间的研究，提出了模具和树脂粉料加热时间的计算方法。
The influences of powder particle diameter and processing conditions upon the factors like product property, inner structure and existence of oxide in rotational molding processing were discussed.
本文讨论了摇摆滚塑成型中粉料粒径大小、工艺条件等对产品性能、内部结构、氧化物的存在及诸因素的影响。
The process of rotational foaming molding of liquid reactive resin was studied, with unsaturated polyester resin as the shell of unfoamed resin moulded part, and polyurethane as foamed core layer.
以不饱和聚酯树脂作为非发泡树脂成型制品的外壳，用聚氨酯树脂发泡形成泡沫芯层，研究了液体反应树脂的旋转模塑发泡成型泡沫夹层制品的工艺过程。
The base theory would be found though the study of plastic heated by microwave for the succedent rotational micro-wave heating molding.
微波加热塑料的研究，主要是为日后滚塑工艺微波加热研究提供理论依据。
The base theory would be found though the study of plastic heated by microwave for the succedent rotational micro-wave heating molding.
微波加热塑料的研究，主要是为日后滚塑工艺微波加热研究提供理论依据。
应用推荐