In this paper, to balance the requests from different components in IoT system, an adaptive multiple sampling rate scheduling (AMSRS) algorithm is proposed.
为了平衡物联网系统的不同组件的要求，本文提出自适应多重采样速率调度算(AMSRS)。
The feasibility of multi-bit rate optical code division multiple access system is experimentally demonstrated.
实验验证了线性组合码多速率光码分多址接入系统方案的可行性。
Single code and multiple code transmission schemes which can provide variable rate services are presented in a WCDMA system.
WCDMA系统提出了单码和多码两种多速率传输方案。
Numerical results indicate that there is an optimum mass fraction of multiple PCMs for the LTES system to reach the maximum heat transfer rate.
数值结果表明，存在一个最佳的质量分数的多个为LTES系统的相变材料来达到最大的热传递率。
This kind of optical fiber can operate in single mode or multiple mode effectively, and is especially suitable for high-bit rate communication system.
这种光纤能以有效的单模方式工作或以有效的多模方式工作，且这种光纤非常适用于高比特率通信系统中。
This paper describes several system structures with multiple antennas and analyzes their performances from the viewpoint of bit error rate and bandwidth efficiency .
本文介绍了具有多个天线系统的几种不同构成方式，从系统误码率和频带利用率两个方面讨论了不同构成方式对系统的改善。
Based on analyzing the two multiple modulation schemes, the expressions of symbol error rate (SER) are presented and the system performances are compared.
在对两种多进制调制方式进行分析的基础上，分别给出了系统误符号率(SER)的表达式并进行了仿真比较。
In MIMO system, multiple antennas are used separately at the transmit and the receive ends. MIMO technique is used to improve channel capacity and link reliability as well as to reduce bit error rate.
多进多出（MIMO）系统在发射端和接收端分别设置多副发射天线和接收天线，采用MIMO技术可以提高信道容量和信道可靠性，降低误码率。
The scheme of hybrid WDM and optical code division multiple access (OCDMA) system is proposed and its blocking rate is analysed.
提出混合波分复用(WDM)和光码分多址(OCDMA)网络结构方案，并建立数学模型讨论该网络结构的阻塞率。
Results The death rate was obviously higher in patients implicating in acute renal failure concurrent multiple system organ failure than those suffering acute renal failure only.
结果急性肾功能衰竭合并多脏器功能衰竭的患儿病死率明显高于单纯急性肾功能衰竭。
The hydraulic system of injection molding machine is the representative example, it need to control cylinder speed and hold pressure, so it indeed to use pressure and flow rate multiple valve.
在注塑机液压系统中，要求能在注塑油缸运动的过程中对其进行速度控制和在保压过程中进行压力控制。 这就需要用到压力-流量复合阀来进行压力和流量的控制。
The hydraulic system of injection molding machine is the representative example, it need to control cylinder speed and hold pressure, so it indeed to use pressure and flow rate multiple valve.
在注塑机液压系统中，要求能在注塑油缸运动的过程中对其进行速度控制和在保压过程中进行压力控制。 这就需要用到压力-流量复合阀来进行压力和流量的控制。
应用推荐