The effect of charges remaining on a dielectric plate upon the 50% impulse surface flashover voltage U_ (50) in the non-uniform field (rod-plane gap) is investigated.
针对不均匀电场(棒-板间隙)中绝缘板上残余电荷对50%冲击闪络电压u _(50)的影响做了一些试验研究。
When equipment slotted side gap, face plate electrode and groove, perpendicular to the bottom of the shell and necessary.
当设备有槽侧的隔阂时,面临电极板和槽,壳有必要垂直于底部。
Ventilating tubes are made of galvanized steel plate, the gap between the joint of air tube and air well should be filled with incombustible materials.
通风管采用镀锌钢板制作,风管与风井连接处缝隙应用不燃材料填实。
There is great gap between theory research and current development about press plate wood vacuum dryer, especially wood vacuum drying schedule which can not meet the requirement of production.
目前,国内对于压板式木材真空干燥机的理论研究与实际还有很大的差距,尤其是木材真空干燥工艺基准不能适应实际生产要求。
A motor shaft gap used for a sealing plate for a seal air channel is left between the belt pulley and the end cover of the motor shell.
在皮带轮同电机机壳端盖之间保留供密封风道用的密封板穿过的电机轴空隙位。
HGC system is the important component in the control system of coldroll, it can control the rolling gap size of stand, and direct effect the shape of plate.
液压压下控制系统是冷连轧机控制系统中十分重要的组成部分,它主要实现机架辊缝大小的控制,对于轧制板材的板形有着直接的影响。
The charge simulation method for the calculation of the electric field intensity in the rod-plate gap is also briefly introduced.
为了进行外加场强的计算,文中还简介了用模拟电荷法计算棒——板间隙场强的方法。
Then a retraction less variable precision gap setting method was put forward based on the characteristic of plate gap setting.
基于此特性,提出中厚板电-液联合辊缝设定新方法?无回缩变精度快速辊缝设定法。
For high ozone content and efficiency, the discharging behavior and performance of a plate-type micro-gap ozone generator were studied.
以获得高效率高浓度臭氧为目标,研究了平板式微间隙臭氧发生器的放电特点和性能。
Real plate gap means the clearance between the surface of stationary disc and the surface of rotating disc in refining zone.
磨盘实际间隙是指动磨片和定磨片在研磨区内齿表面之间的距离。
The LIM has the second longitudinal end effect caused by eddy currents in secondary plate in its operation, which reduces its available magnetic flux of air gap and pull coefficient.
单边直线感应电机运行中因次级板产生涡流而存在第二类纵向边缘效应,造成气隙有效磁通和牵引力系数降低。
The influence of data treatment method for measured force and gap and plate crown on gauge calculation is also analyzed.
同时分析了实时轧制力和辊缝数据的处理方法对厚度计算的影响。
In the thesis, a non-contact measurement technology by combining an eddy current displacement sensor with a sonic thickness sensor was put forward to measure timely real plate gap of refiner.
本文对采用电涡流传感器和超声波测厚仪组合实时非接触测量磨盘真实间隙的设计方案进行了研究和探讨。
The contact measurement is widely used to measure plate gap, but the method can't timely indicate the change of plate gap caused by plate wear.
目前普遍采用接触式测量方法不能实时反映磨片磨损后的真实间隙。
The gap crown between two work rolls of plate mills and the strip shape can be adjusted by axial shifting of the work rolls, both of them have a special contour.
板材轧机上一对带特殊辊型的工作辊轴向相对移动时,可改变辊缝凸度,调节板形。
Plastic deformation is easy to occur on the surfaces of plate and strip in the roll gap of pinch mill.
在板带递送机辊缝变形区中,板带表面容易发生塑性变形。
We present the results of an aging test on two six-gap multi-gap resistive plate chambers (MRPC) designed for the RHIC-STAR TOF system.
给出了为RHIC-STAR飞行时间探测器设计的多气隙电阻板室(MRPC)的辐照实验结果。
As by the two sides of the diaphragm metal plate is placed, changes of gap caused by deformation of diaphragm lead to changes of capacitance accordingly.
膜片两侧置有金属板,膜片变形引起的间隔变化将使电容之发生变化。
The gap on the front end of the steel plate is in a rectangular shape.
所述的钢板前端的缺口为长方形。
The gap portion defines at least a portion of the cooling passage, and is formed by at least an edge on one side of the top plate and the cabinet separated from each other.
间隙部分限定冷却通道的至少一部分,并至少由彼此分离的在顶板一侧上的一个边缘和橱柜形成。
We also investigate that both increasing the width of medium plate and the radius of embedded concentric circle are in favor of the new band gap emerging.
通过改变相关参数我们发现增加介质平板的宽度,增大内嵌介质柱的半径都有利于新禁带的产生。
An assembly step matching the shaft shoulder of the mainshaft is positioned on the shaft sleeve and a fixed gap forms between the shaft sleeve step and the water-tight plate.
轴套上设有与主轴轴肩配置的装配台阶,轴套台阶与水密封板之间形成有固定的间隙。
The ground plate is arranged on one side of the dielectric plate 2 with a gap arranged at the middle, which is fed with the power to the radiating element through the gap.
接地板位于介质板2的一面,在中心开一缝隙,通过该缝隙对辐射单元进行馈电。
It is compression molded as a whole, of the same plane with the surface plate, to avoid a large connection gap, so as to look nice and be easy to clean.
整体压缩成型,与平面板为同一平面,避免较大接缝,以达到美观、易于清洗的效果。
The production of the multi-strip multi-gap resistive plate chambers for FOPI sTime-of-Flight(TOF) upgrade was accomplished.
为提高德国FOPI系统飞行时间的探测本领,运用新型多条多气隙阻性板探测器对FOPI系统进行升级改造。
The top end of the honeycomb tubular supporting component is fixed with the top plate by adhesive technology. The top plate does not make linear contact with the unfolded side, but leaves a gap.
在蜂窝型管状支撑件上方采用胶粘工艺固定顶层板,顶层板与底层板的弯曲折边不形成线性接触,形成缝隙。
By the influence function method the influence of plate width, work roll radius, backup roll radius, work roll crown, backup roll radius and rolling force on gap setting were calculated.
根据影响函数法计算轧辊凸度对辊缝设定的影响,当保持工作辊和支承辊凸度不变,则轧制力与辊系弹性变形呈线性关系,工作辊和支承辊凸度的变化对直线的斜率几乎没有影响。
By the influence function method the influence of plate width, work roll radius, backup roll radius, work roll crown, backup roll radius and rolling force on gap setting were calculated.
根据影响函数法计算轧辊凸度对辊缝设定的影响,当保持工作辊和支承辊凸度不变,则轧制力与辊系弹性变形呈线性关系,工作辊和支承辊凸度的变化对直线的斜率几乎没有影响。
应用推荐