The designing of control arithmetic.
控制算法设计。
The research on the data process and control arithmetic.
数据处理与控制算法的研究。
Secondly, analysis and research of control arithmetic of magnetic bearing .
分析和研究了磁力轴承控制器控制算法。
At last, bit pressure control arithmetic based on fuzzy theory is compiled.
最后完成了对于钻压模糊控制算法软件的编制。
We design a novel multi-phase fuzzy traffic control arithmetic for single intersection.
设计了一种针对单交叉口的新的多相位模糊交通控制算法。
Based on the control theory of sate-feedback, designing a path tracking control arithmetic.
根据状态反馈控制理论，设计了移动机器人路径跟踪控制算法。
A path tracking control arithmetic is designed based on the control theory of sate-feedback.
根据状态反馈控制理论，设计了移动机器人路径跟踪控制算法。
At last, the article expatiate the process of the fuzzy control arithmetic realized on the PLC.
最后，阐述了模糊控制算法在PLC上实现的过程。
Integrating intelligent and PI control arithmetic, we obtained a fuzzy hybrid controller based on PI.
本文将智能控制算法和PI控制算法相结合，提出了一种基于PI的模糊混合控制器。
The system proves that the control arithmetic is available and valid during the debugging and the working.
样机系统的调试和工作证明该算法是可行和有效的。
The object of the control arithmetic is to make the traffic trunk road unblocked and the average vehicle delay time shortest.
控制算法在保证交通畅通的情况下，使车辆延误时间尽可能地短。
The fuzzy-PID control arithmetic based on adaptive parameter is proposed by the characteristics of fuzzy system and PID system.
针对模糊系统和PID系统的特点，提出了模糊pid参数自调整的控制算法。
In this paper parameter adjustment fuzzy control arithmetic of non invasive oxygen saturation ward apparatus is introduced in detail.
详细介绍无创脉搏血氧饱和度监护仪参数调整的模糊控制算法。
This paper introduced the hardware structure and control arithmetic of load's anti-swing control system of overhead and gantry crane.
介绍了桥门式起重机吊重防摇控制系统的硬件结构和系统控制策略。
Then the paper discusses method of robot's kinematics and inverse kinematics and robot's control arithmetic mostly about PID control.
然后，本文探讨了机器人运动学正逆解求解方法和伺服电机控制算法，详细地讨论了其中的PID算法。
The composition, working principle and control arithmetic of a high - speed aviation engine clutch bearing test machine is introduced.
介绍了一种高速发动机离合器轴承试验机测控系统的组成、工作原理和控制算法。
This article mainly completed structure design, building of embedded control platform and control arithmetic of the Wall Climbing Robot.
本文主要完成了壁面攀爬机器人结构设计、嵌入式控制平台的搭建和控制算法的实现。
Finally, we present a new control scheme of air pressure and flow and build PID decoupling control arithmetic based DRNN of air control system.
最后，提出了新的气源压力、流量系统控制方案，建立了对气源压缩空气压力、流量系统的基于神经网络整定的PID解耦控制算法。
Fuzzy optimal control arithmetic was designed for each module, and an improved BP neural network was introduced to implement the fuzzy relation.
对每个控制模块设计了相应的模糊优化控制算法，并用改进的BP神经网络实现算法的模糊关系。
It could carry through the motion control arithmetic of mono-CPU, parallel bi-CPU and layering multi-CPU and research on system support software.
它可以进行单cpu、并行双cpu和层次化多cpu的运动控制算法和系统支撑软件的研究。
Maths are setup, group-controled system control arithmetic are discussed using the knowledge of the dark synthesis judgement in the applied mathematics.
本文利用应用数学中的模糊综合评判理论对电梯群控系统的算法进行——对应建立数学建模。
A new main-steam temperature control scheme of utility boiler is proposed by combining the dynamic matrix control arithmetic with the cascade control structure.
将动态矩阵控制算法与串级控制相结合，提出了一种新的火电厂锅炉主汽温控制方案。
In order to realize synchronous control, distributed motor synchronous control system based on PLC and frequency conversion and PID control arithmetic are adopted.
本文提出了基于PLC和变频调试技术的集散式同步控制方案和采用PID控制算法实现多电机的同步控制。
Aiming at the position servo system of NC machining tool, this paper designs a kind of control arithmetic on compound sliding variable structure for its controller.
针对数控机床的位置伺服系统，为其控制器设计了一种复合滑模变结构控制算法。
This paper introduces a hydraulic synchronous system, which USES a new-type digital valve as synchronous controller and makes use of a fuzzy-PID control arithmetic.
介绍了一种以新型数字同步阀为同步控制元件，运用模糊pid算法进行控制的液压同步系统。
The principle of indirect strain control based on slip compensation of inverter is analysed. Its realizing means, control arithmetic and applied effect are presented.
分析了基于变频器滑差补偿的间接张力控制原理、实现方法及相应控制算法，给出了应用效果。
On the control arithmetic, mainly discussed batch reactor temperature control policy, general analysis batch reactor temperature's characteristic and control difficulty.
在控制算法方面，主要研究了间歇过程的温度控制策略，全面分析了间歇式反应釜温度变化的特点及控制难点。
The paper study the principle of state point's movement in state space, and through the energy optimized control arithmetic, to reach the aim of energy optimized control.
结合能量最优控制算法研究状态点在状态空间移动的规律，以达到能量最优控制的目的。
Finally, as to the control arithmetic, PID and fuzzy control are colligated to improve the control precision and speed, which is helpful for solving the similar problems.
最后，控制算法方面运用了基本PID控制与模糊控制相结合的控制算法，达到了较高的控制精度和速度，而且对于类似问题的解决具有借鉴意义。
Finally, as to the control arithmetic, PID and fuzzy control are colligated to improve the control precision and speed, which is helpful for solving the similar problems.
最后，控制算法方面运用了基本PID控制与模糊控制相结合的控制算法，达到了较高的控制精度和速度，而且对于类似问题的解决具有借鉴意义。
应用推荐