Based on reliability theory, combined with finite element method for structure optimization, the lightweight design for the lower arm of a suspension is conducted.
基于可靠性理论，结合有限元结构优化方法进行某悬架下摆臂的轻量化设计。
In this master thesis, the stress-strain relationships of thin films were measured by nanoindentation combined with dimensional analysis and finite element method.
本文以纳米压痕法结合量纲分析及有限元方法来测量薄膜材料的应力-应变关系。
The Monte Carlo method combined with the elastoplastic finite element method (FEM) is proposed to analyze the slope stability problems.
蒙特卡洛随机搜索法与弹塑性有限元法结合，求解边坡稳定问题。
And then obtained the modification model of sensor shell with sufficient accuracy by adopting the combined modeling method of experimental modality analysis and finite element modeling.
然后采用实验模态分析和有限元建模相结合的建模方法，获得了足够精度的传感器壳修正模型。
This paper used the finite element method to compute the temperature field, and combined finite element with analytic solution to develop a calculation of thermal stresses.
本文采用有限元数值分析方法计算多层圆管的温度场，并把解析解与有限元相结合，提出一种求解其热应力的计算方法。
A finite element model of large combined tubular reactor with complicate structure and loads was built up.
对结构和所受载荷都非常复杂的某大型组合管式反应塔建立了有限元模型。
The above-mentioned methods are combined to optimize the field of the breaker, and the calculation results are compared with the results calculated by finite element method.
本文将上述方法结合起来对断路器的电场进行优化计算。并将计算结果与有限元法的计算结果进行了分析比较。
Finite element analysis program was used to calculate the stress of 300mw turbine rotor in straightening the axle, and the effect of each factor is analyzed combined with the trial result.
应用有限元分析程序对300MW汽轮机转子直轴进行了应力计算，并对各影响因素进行了分析，结果表明退火处理过程中残余应力产生的塑性变形量不可忽略。
A local transmitting boundary is combined with a lumped-mass finite element technique to form a mechanical model simulating the near field steady wave motion.
本文将局部透射边界和集中质量有限元技术结合起来形成一个模拟稳态近场波动的力学模型。
Remote field eddy current technique combined with computer technique and finite element analysis was used to examine the inservice ferromagnetic heat exchanger tubing.
远场涡流技术结合计算机技术和有限元分析方法，解决了在役铁磁性材料换热器管检验的问题。
This paper uses inverse finite element method combined with forward finite element method to design blank of automobile panel, and proves its rationality by physical simulation.
本文采用有限元逆向法和正向法结合的方法，确定覆盖件零件的成形毛坯，并用物理实验验证了其合理性。
In this paper, a discrete local transmitting boundary is combined with a lumped-mass finite element technique for simulating steady wave motion in the viscoelastic layered medium.
本文将离散的局部透射边界与集中质量有限元方法相结合，用于模拟粘弹性成层介质中的稳态波动。
The experimental results were used to calculate material properties, using the finite element method combined with optimization techniques.
该方法根据实测的客观物理量集成运用有限元方法和优化技术来测算材料的弹性参数。
Objective:To conduct such a study on TSS downstream of mitral stenosis using a finite element model of two dimensions combined with Doppler echocardiography in human beings.
目的探讨一种与多普勒超声相结合的人体二尖瓣狭窄下游湍流剪应力二维有限元分析方法。
This paper uses the combined finite-discrete element method with smeared rotating crack model to analyze the seismic rupture process simulation of concrete gravity dam under the action of earthquake.
应用联合有限-离散元法结合弥散式旋转裂缝模型分析了地震作用下混凝土重力坝动力破坏过程。
Combined with the finite element method, the semi-analytical numerical method presented can be used to analyze thick composite laminates with arbitrary boundary conditions and geometrical shapes.
进一步和有限元法相结合，得到了能够分析具有任意边界条件和几何形状的复合材料叠层厚板的半解析数值方法即哈密顿单元方法。
The finite element method is combined with homogenization theory based on asymptotic expansion for predicting effective properties of polymer matrix composites toughened and strengthened by particles.
将数学上的均匀化方法与有限元法相结合，预测了颗粒增韧增强聚合物基复合材料的有效性能。
A combined iteration method for load identification is proposed to analyze the nonlinear dynamical system by joining finite element method with active control method.
针对一类非线性系统提出了一种新的载荷识别方法，组合迭代法。
According to practical working situation, nonlinear dynamic finite element method is adopted to establish a numerical model of combined breaking rock with high pressure water jet and mechanical bit.
采用非线性动态有限元法，结合实际工况条件，建立了高压水射流—机械齿联合破岩的数值模型。
Combined with general four-node element around crack tip element, a new hybrid finite element method to study stress intensity factors for interfacial crack is introduced.
与四节点单元相结合，由此提出了一种新的求解应力强度因子的杂交元法。
In this paper the finite element method is combined with optimization. The strengthening optimization is put forward on the basis of the limit analyse method of pressure vessel strengthening design.
将有限元应力分析方法与优化设计方法相结合，提出了基于受压容器开口补强的极限分析理论和优化设计思想。
Combined with analysis on observation data and relation between seepage and water level, as well as seepage regression analysis and finite element method, the paper studied dam seepage, for reference.
本文通过对大坝观测资料、渗水量与水位关系和渗水量回归分析，利用有限元方法，对大坝渗透破坏现象进行初步分析，为运行管理提供参考。
In this paper, the component mode synthesis, combined with the perturbation and stochastic finite element, is used to study the random eigen problem of large and complicated structures.
采用子结构模态综合和摄动随机有限元相结合求解工程结构的随机特征问题。
Let the mechanical dynamics be combined with the method of finite element analysis to establish the simulation method of vibration measurement of dynamics balancing test-bed of mechanism.
将机械动力学与有限元分析方法相结合，建立了机构动平衡实验台振动测量的仿真方法。
This paper, combined with the task of the FMS fixture design, describes the application of Finite Element Method in the fixture design, in addition the application results are also presented.
本文结合FMS夹具设计任务，介绍了有限元法在夹具设计中应用的方法和所取得的结果。
The effects of muscle loadings on bone remodeling were investigated using an orthotropic algorithm combined with a finite element (fe) model based on computed tomography (ct) data.
该文基于CT数据建立股骨有限元模型，用正交异性算法仿真了肌力对骨再造的影响。
Combined UG with ADINA, the finite element model of the whole as well as the double roller of high capacity roller dollies were separately established.
将UG三维建模软件和ADINA软件相结合，分别建立了大负荷滚轮推车的整体和双滚轮的有限元模型。
Combined UG with ADINA, the finite element model of the whole as well as the double roller of high capacity roller dollies were separately established.
将UG三维建模软件和ADINA软件相结合，分别建立了大负荷滚轮推车的整体和双滚轮的有限元模型。
应用推荐