增大中心距。
Applicable for all cylinder of different diameter by adjusting the trolley center distance.
通过调整滚轮的中心距，适用不同直径筒体。
In certain conditions, the center distance reduction will cause additional radial pressure of two mating gears.
在一定条件下，这种中心距缩减会导致互相啮合的两齿轮间产生附加径向压力。
All of this got data reference and design basis for eccentric mechanism for adjusting the center distance and others.
通过优化为楔横轧机偏心中心距调整机构及相关机构的设计提供了良好的数据参考、设计依据。
Dies seat: Adopt West Germany technology (Inlay type), assure the drawing center distance to avoid the wire breakage.
模座：采用西德技术(镶入式)，保证拉伸的中心距，减少断线机率。
The best tightness is: in the middle of the chain lift or press down, the center distance of the two sprocket is about 2%-3%.
则最好的松紧程度为：链条的中部在提起或压下的时候，两链轮中心距的约为2% - 3%。
The conjugate principle of the variable ratio gear with constant center distance and constant contact Angle has been analysed.
研究了定中心距、定啮合角变速比齿轮的啮合原理。
Through orthogonal experiment, parameter of back zone draft multiple, roller center distance and roving twist factor are selected.
并通过正交试验对后区牵伸倍数、罗拉中心距和粗纱捻系数进行了优选。
The center distance of two holes is equal to the center distance of the corresponding venting hole and the water hole of the boiler.
两孔的中心距与相应锅炉通气孔、通水孔的中心距相等；
The ionospheric up flowing ion mainly distributes in the near geo space and its flux has a negative gradient versus geo center distance.
上行离子主要分布在近地空间，其通量密度相对于地心距离呈负梯度。
When sailing in waves, ship hull total bending deformation will reduce the center distance of gear backing radially arranged in ship hull.
船舶在波浪中航行时，船体总弯曲变形会使沿船体纵向布置齿轮机构的轴承支座中心距产生缩减。
Tensile strength was found to decline with increase of the ratio of average chord lengths of the two phases (L1/L2) and mass center distance (D).
结果表明，当分散相一定时，拉伸强度随两相相对尺寸的增大和分散相颗粒相关性的减弱而减小。
Under certain conditions, this reduction of the center distance will lead to additional radial pressures between two meshing gears in the gearing.
在一定条件下，这种中心距缩减会导致互相啮合的两齿轮间产生附加径向压力。
This paper deals with the engagement of gears with circular arc profile in normal plane at the presence of errors on center distance and depth of cut.
本文讨论了法向圆弧齿轮在有中心距偏差及切深偏差时的啮合。
In this paper, the center distance of driving gear is assembled according to the normal, left and right, then research its effect to micro-vehicle rear axle vibration.
本文对主动轮的中心距按照正常、向左和向右三种情况下进行装配，研究其对微车后桥振动的影响。
The basic parameters of non-circular gear are determined, such as primary circle, eccentricity ratio, eccentricity throw and proportional coefficient of center distance.
确定了非圆齿轮的基本参数：基础圆半径、偏心率、变形距和中心距比例系数。
The selection of center distance and gear ratio distribution for a reducer with double-circular-arc gear will have a direct effect on its size, weight and loading capacity.
双圆弧齿轮减速器中心距和传动比分配的确定，直接影响减速器承载能力、重量和体积。
The polar equation of non-circular gear pitch curve, calculation method of center distance, formula of pitch curve length, primary circle radius and pressure Angle is given.
给出了非圆齿轮的节曲线极坐标方程，两齿轮中心距的计算方法，节曲线长度、基础圆半径和压力角的计算公式。
This paper describes the camera calibration algorithm which is needed when given only the center-to-center distance between adjacent CCD sensor elements in the vertical distance.
本文阐述了在只给出CCD成象面垂直方向相邻光敏元的距离时的摄象机校准算法。
The knife tooth part is the rectangle, through adjusts two cutter surface knife's center distance, cannot replace the cutter, can cut many kinds of different widths on the noodles.
刀齿部分为矩形、通过调整两切面刀的中心距，不需更换切刀，就能切出多种不同宽度的面条。
Based on the principle of gear machining generating method, a modeling method - variable center distance gear modeling method for variable ratio gear sector profile is put forward.
基于齿轮的范成加工原理，提出了一种变速比齿扇齿廓的定中心距齿轮建模法。
In order to solve the sparseness of LS-SVM results and restrain the influence of the sample-outliers, a new method of optimized samples by part samples center distance is presented.
为了克服LS-SVM解非稀疏性的缺点，同时抑制偏差较大的训练样本对海底趋势面构造的影响，提出一种基于局部样本中心距离的训练样本优化方法。
The Park is located in the east of the master city planning area of Xiaogan city. It is next to the international metropolis Wuhan, center distance between the two cities is only 60km.
园区位于孝感市城市总体规划区的东部，毗邻武汉国际大都市，两市中心距离仅60公里。
It can measure not only the inner diameter, outer diameter and linearity error, but also the center distance between holes, taper and position errors such as coaxality, verticality, etc.
它不仅可以测量内径、外径和直线度误差，还可以测量孔中心距、锥度和同轴度、垂直度等位置误差。
By using geometry analysis method, this paper educed calculation formula of normal direction gear side clearance when internal gearing involute gear transmission center distance waned slightly.
通过几何分析的方法，导出了内啮合渐开线齿轮传动中心距略变小时，法向齿侧间隙的计算公式，供齿轮传动设计计算之用。
Appropriate pitch curve designing is a key of regularly working for non-circular planetary gear mechanism with variable center distance which can be used in low speed high torque hydraulic motor.
合理的节曲线设计是可用于低速大扭矩液压马达的变中心距非圆行星齿轮机构正常工作的关键。
CDCPM describes the feature space of model by center distance normal distribution (CDN), and simplifies and improves the HMM efficiently by getting rid of the state transition probability matrix a.
CDCPM用中心距离正态(CDN)分布描述模型特征空间，去掉了H MM的状态转移概率矩阵a，对HMM进行了简化和改进。
In their model, the radius is the distance from the center of the animal to its skin.
在他们的模型中，半径是动物中心到其皮肤的距离。
In their model, the radius is the distance from the center of the animal to its skin.
在他们的模型中，半径是动物中心到其皮肤的距离。
应用推荐