通过分析每个条纹升降的方式，系统软件在不到一秒的时间里就可构造出手指表面的三维模型，保证每个峰谷都处在各自合适的位置上。
By analyzing the way each line rises and falls, the software builds a 3-d model of the surface of the finger in less than a second, with each ridge and valley in its proper place.
通过解决激光加工中材料表面温度测量装置的难点，设计了一套新型光学系统，并给出了测量误差分析及结论。
A new optical system is designed for the material surface temperature-measuring device used in laser processing. The measurement error analysis and conclusions are presented.
利用该测量系统对不同材质、不同加工工艺的物体表面的激光反射分布进行了初步的测量和分析。
Primary measurements and analysis of surface reflectance of varied substance along with various machining process are carried out with this system.
分析了在通用硬件平台上结合软件设计的声表面波谐振器无源无线传感虚拟仪器系统。
A virtual instrumentation system for wireless sensing using passive surface acoustic wave sensors is presented. It is designed in light of software on common hardware platform.
分析了除湿系统中直接蒸发式表面冷却器在结霜工况下的换热特性，特别是结霜速度、结霜时间以及结霜时的换热计算。
This paper analyzes some heat-exchange characteristics of evaporator on the condition of frosting in the desiccation system, especially of frost velocity, frosting time and heat exchange calculation.
本文介绍由表面浮标、缆和中间物体组成的综合海洋缆系统动力学特性的二维时域分析方法。
A two-dimensional time domain met hod is presented for the analysis of dynamic behaviour of the ocean cable system in wind, wave and current.
通过有限元分析，研究了950开坯机压下系统球面轴承表面正压力的分布情况，并据此提出了相应的改进措施。
The positive pressure distribution on the bearing surface of screw down system of 950 primary mill was studied using FEM and the corresponding improvement way has been put forward.
本文针对假肢等人-机仿生系统肌电控制装置的特点，研制了一种小型表面EMG测试与分析系统。
To meet the requirement of developing myoelectric controller for a man-machine systems, a surface electromyography (EMG) detection and analysis system is discussed in this paper.
通过分析声表面波谐振器对不同激励信号的响应，本文选用正弦脉冲串作为激励信号，来提高系统工作效率和传感距离。
Through the analysis of the response of resonator base on different pumping signals, sine burst is used for pumping signal of the system to improve the efficiency and detecting-distance.
分析了反渗透系统中膜体形变、水体粘度与表面张力等参数的温度特性。
The temperature properties of membrane deformation, water viscosity and surface tension in reverse osmosis system are analyzed.
分析了影响带钢表面清洁度的各种因素，包括乳化液类型及性能参数、乳化液系统和轧制的工艺参数。
Various factors influencing the strip steel surface cleanliness were analyzed, including the type and performance parameters of emulsion, emulsion systems and rolling process parameters.
根据摩擦学原理，采用动态磨损模拟试验和表面微观分析研究的方法和技术，对气门动态磨损特性进行了系统的试验研究。
The wear properties of valve are systemically investigated by using dynamic simulation testing and surface microscopic analysis techniques based on principle of tribology.
分析铜箔表面质量缺陷对电力变压器电气性能的影响，研究采用机器视觉系统对铜箔表面质量缺陷监视的关键技术。
The influence of copper foil surface quality on electrical performance of power transformer is analyzed, the key technology for monitoring the surface flaw with machine vision system is studied.
对测量系统进一步开发，可做成测量细胞表面电荷的生物分析芯片。
Further exploitation to this measure system, it can be made into biology analysis chips to measure the surface-charges of cells.
在曝气系统的选择上，比较分析了微孔曝气系统和表面曝气系统，提出了如何提高微孔曝气和表面曝气系统的可调节性能的一些措施。
Primarily, some currently applied aerate system are compared, some method is presented to improve the miraco bubble aerate system and the surface aerate system.
本文给出了表面多次波衰减方法的研究现状的系统阐述，并分析了表面多次波衰减研究的发展趋势。
The research progress in SRM attenuation is presented in this paper, and also the SRM future research direction.
系统地分析和探讨了等离子束表面冶金设备的核心部件等离子炬的设计、表面冶金的合金材料的选择、表面冶金工艺的确定。
The design of plasma torch, which is the center part of surface metallurgy equipment by plasma-jet, the selection of alloying powder and processing parameter are analysed in the paper.
介绍用红外热成象系统检测材料表面和内部缺陷的方法和实验结果，并分析热图的变化规律。
Detection of surface and inner surface flaws in materials by infrared thermal imaging system and its experimental results are described. The regularity of thermal images is also analysed.
本文还对激活表面及热清洁工艺进行了系统地分析，确定出了最佳的表面清洁温度及时间。
The activation surface and the process of heating cleaning have also been analyzed systematically and the optimum temperature and time for surface cleaning have been determined in the paper.
该系统以CCD为传感器，与微型计算机连接，进行三维编织复合材料预制件表面编织角的检测，并对其进行不匀分析。
A system consisting of CCD sensor and computer may be used to test surface braiding Angle of three dimensional composite material preform, and analyse its unevenness.
通过对6480型驱动桥的噪声功率、表面声强、表面声压、表面振动加速度以及相应的时频谱进行了全面、系统的测量和分析。
The noise power, sound intensity, sound pressure, vibration acceleration and corresponding time-frequency spectrum of 6480 driver axle surface were measured and analysed.
光学系统杂光分析对航天航空、精细细微分析领域的光学设计有着重要意义，其首要问题是研究光学系统中典型受光表面的散射模型。
The first problem is to study the model of scattering from typical surfaces in your optical system before stray light is analysed in this paper.
对内燃机缸盖系统的振动激励及表面振动信号的特性进行分析，建立了缸盖系统的振动模型。
This paper analyses the properties of the excitation and response of an engine cylinder head system and establishes the vibration model of the cylinder head system.
本文对JHC6400型汽车后桥的噪声功率、表面声强、表面声压、表面振速及相应的频谱等进行了全面、系统的测量与分析。
The noise power, sound intensity, sound presure, vibration velocity and corresponding frequency spectrum of JHC6400 rear axle surface were measured and analysed.
地理信息系统(GIS)是一种以采集、贮存、管理、分析和描述整个或部分地球表面与空间地理分布有关数据的空间信息系统。
Geographical information system (GIS) is a spatial information system which is in charge of collecting, storing, managing, analyzing and describing data related spatial distribution.
该分析系统对所采集的角膜前表面光栅映像直接分析处理，计算出角膜前表面若干个点的曲率半径和屈光度。
It might analyse the images Which were caught from the anterior surface of the cornea directly and calculate the radial curvature and refraction of the points on the anterior corneal surface.
其次，使用由FFT快速傅立叶分析仪、激光传感器等组成的检测系统，进行了激光传感器对木材表面粗糙度定量测量方法的研究和木材表面缺陷识别的研究。
Secondly, laser sensor quantitative measure wood surface roughness method and wood surface defect recognition are studied by the test system consisting of FFT analyzer, laser sensor etc.
轧辊表面缺陷检测是轧辊辊型在线检测系统中的一个重要问题，它直接影响着带材产品的质量，传统的检测方法和数据分析方法已经很难适应现代的轧制生产。
Detection of roller surface defect is an important question in the roller profile online measurement system. It has direct effect on the quality of the strip steel products.
本文对喷涂载体表面进行了反应动力学分析，提出了系统理想状态下的光净化速率方程。
The dissertation carried out the reaction kinetics analysis of the sprayed carrier surface, and put forward the photo-catalytic purification rate equation under ideal state.
本文对喷涂载体表面进行了反应动力学分析，提出了系统理想状态下的光净化速率方程。
The dissertation carried out the reaction kinetics analysis of the sprayed carrier surface, and put forward the photo-catalytic purification rate equation under ideal state.
应用推荐