文章主要对华东师范大学文学院大跨度连廊中应用现浇混凝土空心楼盖及滑动支座设计等作一介绍。
The application of cast-in-situ hollow concrete floor system in the large span gallery of the Literature Institute of East China Normal University and the design of the slip bracket are introduced.
介绍聚酯装置的真空系统的流程、乙二醇蒸气喷射泵的外型型式设计、支座设计、支座弹簧选择及乙二醇蒸气喷射泵配管设计中的要点。
The vacuum system process of PET unit, the design of EG steam ejector shape and support, the selection of support spring and the main points in the ejector pipe design are introduced.
介绍了该车的车架、传动装置、弹簧支座、弹簧组合和主动轮部件等设计。
The designs of the vehicle's frame, transmission device, spring support, spring combination and driving wheel component, etc. were introduced.
橡胶支座的设计使用寿命建议值为50年。
The proposing value of service life of design was 50 of rubber bearing.
结果表明支座板的设计满足强度要求。
The results shown that the design of the support plate can meet the strength requirements.
利用现有设备并进行相关的设计和改造后，对两组同样规格的支座进行了相关试验。
After correlative designing and modifying existing equipments, two pairs of elastomeric bearings were tested by the inclined compression test method.
介绍针对本桥专门设计的铰轴钢支座和铰轴滑板钢支座施工方法。
In this paper, the construction method for the hinged steel bearings and hinged sliding plate bearings specially designed for the Bridge is presented.
文章基于简化分析和动力实验，讨论了在隔震建筑设计中与叠层橡胶支座稳定性相关的问题。
In this paper, based on the simplified analysis and dynamic tests, the problems related to the stability of laminated rubber bearing in the design of seismic-isolated buildings are discussed.
对大型重叠式换热器支座和壳体的受力情况进行了分析，并给出了校核和设计方法。
The situation of forced shell and support saddle of the giant superimposed heat exchangers is analysed, and the means of designing and checking are presented.
利用内外筒支座条件和截面高度随内力变化的方法设计预应力折线板楼盖。
Taking advantage of bearing factor and the changed section according to internal forces, prestressed folded concrete floor is designed.
为满足工程设计的需要，有必要对宽支座的受力特性及计算方法进行研究。
To satisfy the need of engineering design, it is necessary to study on the loading characteristic and calculation method about wide bearing continuous beam.
为了合理设计防止落梁装置，应用考虑支座破坏影响的非线性动力计算方法研究了防止落梁装置的地震响应。
To reasonably design the girder falling restrainer, the nonlinear seismic response of the restrainer was investigated considering the failure process of the bearings.
指出应考虑多个因素，合理确定隔震支座的设计竖向承载力和水平变位限值。
It is pointed out that in the design of isolated buildings the vertical carrying capacity and limited horizontal deformation of bearings should be confirmed by considering multifactor.
希望本论文将对铅销橡胶支座的设计、应用和生产具有一定的现实参考价值，可以加速铅销橡胶支座的实用化进程。
It is anticipated that this paper would have some referential value to the design, application and production of Lead-Rubber-Bearing and accelerate its process of the practicality.
静力荷载作用下结构的支座形式的设计是十分合理的，但是其减震性能有待于进一步优化。
The form of the supports is designed to be very reasonable to the static load, but its Seismic performance should be further optimized.
将叠层橡胶支座和R／C柱的串联机构作为隔震系统的做法在实际工程中已有应用，但至今尚无规范化的设计计算方法。
The serial isolation system consisting of laminated rubber bearing and R/C column has been applied in practical building, but without the corresponding codes for calculation and design yet.
介绍了朝阳寺水电站扩机增容工程的弧门支座加固的计算、设计及施工措施。
This paper introduces the calculating, designing and construction methods of reinforcement of Chaoyang Temple Hydropower Station's arch-gate bracket.
惰轮支座的设计会有许多不同的方案，应当根据设计准则创造最优的结构型式。
There are many different design schemes for idler gear mounting. We should create the optimum configuration according to the design criteria.
通过拓扑优化设计了自卸车浮动式支撑结构的举升缸支座；
A lifting oil cylinder support with floating support structure was designed by the topological optimization technology.
介绍了不同结构发动机支座支撑脚参数化设计的方法。
This paper introduces the parametric design of engine bearer foot with different structure.
本文介绍了结构方案的确定、网壳的结构分析与设计、支座的构造以及制作与安装等。
In the paper, the derivation of structural scheme, the analysis and design of shell structure, the details of support, as wellas the fabrication and erection of roof structure are presented.
介绍支承在载荷传感器上的大直径大负荷筒仓支座的一种设计计算方法，并给出了一个工程实例的设计计算结果。
Design calculation method for lug of large diameter and heavy load silo which mount on sensor cell has been introduced, and calculation results of a real engineering has been showed.
对南京夹江自锚式悬索桥采用弹塑性阻尼支座进行减隔震设计，并采用非线性动力时程分析方法，对阻尼支座屈服荷载进行了参数敏感性分析。
A new kind of elastic-plastic energy dissipating bearing is applied to the seismic isolation design of the Nanjing Jia River Bridge, a typical self-anchored suspension bridge with single tower.
这说明用固定支座模型进行设计是一种偏保守的方法，用弹性支承模型进行设计具有一定的经济性。
It indicates that design technique of the fixed support model is conservative and that design technique of the elastic support model has certain economy.
最后介绍了预应力混凝土连续曲线箱梁桥的设计，重点讨论了总体设计，钢束预应力的损失的计算，预设支座偏心调整扭矩等设计中的关键问题。
Lastly design of P. C. continuous curved girder bridge is discussed in the paper, in especial prestress reinforcing steel bar's loss and bearing design.
文中介绍了空间桁架支座及跨中节点设计；
介绍了一种位标器支座测试系统的设计和实现。
This paper presents the design and realization of a measurement system for the pedestal of coordinator.
分析了弹力支座的工艺性，介绍了级进模总体设计结构和排样方案。
The manufacturability of the elastic pedestal was analyzed. The general structural design and layout scheme of the progressive die were introduced.
结合实例，对皮带机驱动机构的电机、减速器、耦合器和支座等主要部件进行了选型设计。
Based on the instance, this article introduces some designs of motor, reducer, bearings and other major components of the belt driving mechanism.
公司拥有多名科技研发人员，技术力量雄厚，可根据客户的实际要求设计生产各种类型钢结构支座、橡胶减隔震支座及其它橡胶减振产品。
Many kinds of steel structure bearing, rubber seismic mitigation and isolation bearing and other rubber shock absorber products could be designed and produced according to he requests of customers.
应用推荐