The experiments consisted of the measurement of yield stress, tensile strength and hardness for samples cut from various parts of the forging.
试验包括对取自不同锻造零件的试块的屈服强度、抗拉强度及硬度的测量。
Silicon can obviously improve the elastic limit, yield point and tensile strength of steel.
硅能显著进步钢的弹性极限，屈从点和抗拉强度，故普遍用于作弹簧钢。
Mechanical properties and fracture mechanism of high strength steel sheet with low yield ratio under impact loading have been studied through instrumented impact and quasi-static tensile tests.
通过室温下的仪器化冲击试验和静态拉伸试验，研究一种低屈服比高强度钢板在冲击载荷下的力学性能和断裂机理。
To the problem of more yield strength error in SSAW pipe transverse strip specimen tensile tests, analyze the reason of the error, put forward corresponding solving method.
针对螺旋埋弧焊钢管横向板状试样在拉伸试验时存在的屈服强度误差较大的问题，分析了其误差较大的原因，并提出了相应的解决办法。
Good yield strength and tensile strength.
良好的屈服强度和抗拉强度。
Tensile yield strength was used to quantitatively evaluate the interfacial interactions, which have significant influence on the tensile fracture morphology of the composites.
采用拉伸屈服强度定量表征了界面相互作用的强弱，研究了界面相互作用对三元复合体系拉伸断裂形态的影响。
The results indicate that the ultimate tensile strength of AM60B increases prominently with the increasing of RE, the yield strength and elongation are also improved.
结果表明，AM60B的抗拉强度随着RE的增加有显著提高，屈服强度、伸长率也有所提高。
The results indicated that in low temperature range, the yield strength and tensile strength decreased obviously as temperature increased.
在低温范围内随温度升高屈服强度和抗拉强度明显降低。
A modified theory of metal volume fraction is put forward to precisely predict tensile properties including elastic modulus, yield stress and tensile strength.
提出了修正后的金属体积分数理论，准确预测了材料的弹性模量、屈服应力及拉伸强度。
The effects of textures on the elastic modulus, yield and tensile strength, fracture and fatigue properties as well as some problems on the application of texture strengthening were discussed.
列举织构对钛合金弹性、屈服、拉伸强度、断裂及疲劳等各种性能的影响；讨论了有关钛合金织构强化实际应用的一些问题。
The yield strength, yield tensile ratio and toughness are major quality indexes of steel pipe (board). However, it is quite difficult to determine them reasonably.
屈服强度、屈强比、韧性等是钢管(板)的主要质量指标，合理确定这些指标的数值有相当难度。
The Nitinol alloy has poor mechanical characteristics, such as, tensile strength, yield strength, and elastic modulus and low suitability to a human body.
镍钛锘合金的抗拉强度、屈服强度及弹性模量等机械特性差而且人体适应性低。
The results show the tensile strength, yield strength, hardness and elongation increased obviously due to the decreasing of the grain size of pure Cu after severe plastic deformation.
研究结果表明：经过大变形后，由于纯铜的晶粒得以细化，抗拉强度、屈服强度、硬度和断裂延伸率都显著增加。
Moreover, it is revealed that the deformation resistance in the thermal cycle process is related to the increase of its tensile stress and the decrease of yield strength.
研究进一步表明，材料变形的难易程度又与变温循环过程，热疲劳试样拉伸应力的增加和材料屈服强度的降低有关。
Retain the N80, P110 material original yield strength and tensile strength.
保有了N80、P 110材料良好的屈服强度和抗拉强度。
The simultaneous measurement of the tensile strength, yield strength, stretching rate, elastic modulus, peel strength and power - of time, of a displacement curve.
可同时测量材料的抗拉强度、屈服强度、伸缩率、弹性模量、剥离强度及力-时间，力一位移曲线。
Alloy K500 Mesh has approximately three times the yield strength and double the tensile strength when compared with alloy 400.
合金K 500网屈服强度的大约三倍，并与400合金相比，拉伸强度增加一倍。
In the same case of magnesium content the impact toughness of hot-rolled plates were higher than cold-rolled, while the cold-rolled plates had good tensile and yield strength.
在相同的镁含量的情况下，热轧板的冲击韧性明显高于冷轧板，而抗拉强度和屈服强度显著下降。
The results showed that tensile strength, tensile yield stress and tensile breaking stress were increased with the increase of bore distance;
结果表明，随筛板孔距的增加，其拉伸强度、拉伸屈服应力及拉伸断裂应力均提高；
The results show that the ultimate tensile strength and yield strength of the alloys rise but the total elongation decreases as the temperature of quench medium drops.
结果表明：随淬火介质温度的降低，淬火降温速率提高，合金的强度增加，塑性下降；
The maximum tensile strength and yield strength were gained at peak-ageing, in addition, the elongation decreased with the extension of ageing time.
峰时效时合金的抗拉强度和屈服强度达到最大值，断后延伸率随时效时间的延长有下降的趋势。
When the aluminum content increases, the grain size of cold-rolled annealed panel becomes small, but the hardness, yield strength and tensile strength of stainless steel 439 increase.
随着439不锈钢合金成分中铝含量的增加，冷轧退火板的晶粒尺寸较小，硬度、屈服强度和抗拉强度升高。
Tensile strength should reach 157 newtons per square millimeter, the yield strength to reach 108 newtons per square millimeter.
抗拉强度应达到每平方米毫米157牛顿，屈服强度要达到每平方毫米108牛顿。
Homogenization treatment before the extrusion coarsened the grain size and reduced the tensile strength and yield strength.
挤压前均匀化热处理使挤压态合金的晶粒尺寸粗化，拉伸强度和屈服强度降低。
But the tensile strength will be reduced a little, and the yield ratio increased.
但抗拉强度将随卷曲温度的降低而有少量损失，而屈强比提高。
Precise prediction to Bauschinger's effect values is given based on the study of tensile yield strength for pipes, so does the range of yield strength supplied.
通过对管材抗拉屈服极限的研究，提出要准确地估计包辛格效应值，并应定出供货的屈服极限范围。
Ductile iron regularly produced by NIBCO has a tensile strength in excess of 60,000 pounds. Yield strength is in excess of 40,000 pounds.
通常由美国尼伯科生产的球墨铸铁的抗拉强度都超过60,000磅，屈服强度超过40,000磅。
The yield and tensile strength of the welded joints of the two kinds of materials increase under dynamic loading and prestrain condition that have little effect on the plasticity of structural steel.
两种材料焊接接头在动载和预应变下的屈服强度和抗拉强度均有所提高，但对其塑性影响均不大。
The yield and tensile strength of the welded joints of the two kinds of materials increase under dynamic loading and prestrain condition that have little effect on the plasticity of structural steel.
两种材料焊接接头在动载和预应变下的屈服强度和抗拉强度均有所提高，但对其塑性影响均不大。
应用推荐