Gas content varies as depth of burial, the thickness of roof clay rocks, and working thickness.
瓦斯含量与煤层埋深、煤层顶板泥岩厚度、煤厚呈正相关关系。
Gas content varies directly with depth of burial and working thickness, depth of burial is the main factor which influence the gas emission of Qixing mine.
瓦斯含量与煤层埋深、煤厚呈正相关关系,煤层埋深是七星矿井瓦斯含量的主控因素。
The working principle of continuous pressing machine and the main factors that influenced the thickness of the board are analyzed.
对连续式压机工作原理和影响板厚的主要因素进行了分析。
It was pointed out that the keypoint in designing the special transducer was its working frequency and crystal Angle according to the coat thickness and flaw location.
根据外套壁厚和裂纹位置特点,提出了专用超声换能器的设计关键在于工作频率和晶片倾斜角。
The minimal water film thickness is the basic condition which ensure the water hydraulic static bearing of valve plate working well.
最小水膜厚度是保证配流盘静压支承工作的基本条件。
In This paper, the system composition and working principle of the material thickness measuring meter of ultrasonic sinter-circle-cooling machines are introduced.
介绍了超声波式烧结环冷机料层厚度测量仪的系统构成和工作原理。
Dry magnetic separators operation regulation note the main factors are: the feeding layer thickness (give ore amount), vibration slot vibration velocity, magnetic field intensity and working gap, etc.
干式磁选机的操作调节注意的主要因素是:给料层厚度(给矿量)、振动槽的振动速度、磁场强度和工作间隙等。
The strength and equivalent stress of the remainder wall thickness of reactor shell under new working condition were checked.
对反应器壳体剩余壁厚在新工况条件下的强度和当量应力进行了校核;
The working principle, characteristics and main control parameters of film extruder production line PET film production objective thickness self-control system were introduced.
介绍了拉幅生产线聚酯薄膜生产目标厚度自动调整系统的工作原理、工作特点、主要控制参数。
Insoling machine for California style athletic shoes. Also suitable for sewing working gloves, furs of medium thickness, diving suits, and children's shoes.
使用于运动鞋,加州鞋中底之缝合,工作手套、中厚皮、潜水衣、娃娃鞋。
The available blade is in flexible thickness, and is easy to manage and replace. The roller will not be damaged when blade is replaced, thus achieving high working efficiency.
可以使用的刀片的厚度灵活,刀片便于管理更换方便,更换刀片时不损害辊子,工作效率高。
The air layer is arranged between the dielectric plates 1 and 2, adjusting the working bandwidth of the antenna through adjusting the thickness of the air layer and the size of the gap.
空气层在介质板1和2之间,通过调整空气层厚度和缝隙大小来调整天线工作带宽。
It is mainly for slicing solid wood, engineer wood andother composite board, working efficiency is high, and veneer thickness isuniform.
主要用于实木,科技木和复合板材的切片,工作效率高,单板厚度均匀。
The gland shim is a sealing washer of the refrigerator compressor and before the compressor being assembled examination and grading of the gland shims thickness is a key working procedure.
缸盖垫片是冰箱压缩机的一个密封件,对其厚度尺寸的测量和分选是装配前的一道关键工序。
This paper suggests a method for measuring the thickness of metal plate for working pieces on line using the eddy current sensors without any damage.
提出一种用电涡流传感器实现无损在线测量工件金属膜厚度的方法。
Safeguard procedures must be set around the equipment and use dry board with thickness of 30mm to make working horse block.
在设备周围必须设置安全防护措施,用30m m厚的干燥木板做工作踏台。
The adopted thickness of steel pipe and the economic flow rate in it under different pressure and working conditions are described in this paper.
本文研究钢管的使用壁厚以及不同工作压力及使用状况下的经济流速。
This paper according to working principle and characteristics of four-rolling mill, maintain several method to measure the thickness of coiled sheet which is moving.
根据四辊轧机的工作原理和特点,提出了借助气动元件控制测量力、并利用磁栅传感器进行精密测量的实现方案。
The contractor shall ensure that the thickness gauge is in good working condition and calibrated at least twice daily.
承包方应确保测厚计处于良好的工作状态并每天至少2次进行校准。
The wall thickness testing principle, sensor's structure and working principle are introduced. And experimental research and analysis have been done.
介绍了漏磁法壁厚检测原理、传感器结构和工作原理,并通过实验进行了分析、验证。
Magnetic working substance area is circular arc with certain radial thickness, and has certain gap with stator permanent magnetism block.
磁工质区域为圆弧形,有一定的径向厚度,与定子永磁块间留有一定的间隙。
The shrink shape for thin tube with little shrink rate and bigger thickness difference in the distortion generally demands more working procedures.
对于缩口系数小、变形前后壁厚比较大的薄壁管件的缩口成形,一般需多道工序来完成。
We recommend working with a minimum wall thickness of 2 mm when the wall is connected to other walls on two or more sides, and 3 mm if it's only connected one side.
当模型的侧壁连接多个面的时候,我们建议使用的最小壁厚为2毫米,如果模型的侧壁没有与其它侧壁的连接,则用的最小壁厚应该为3毫米。
Besides, it points out that it is also important to survey the cover coat thickness, the tunnel line shape, the dig in distance, the working …
此外,覆盖土的厚度、隧道线形、掘进距离、工期、竖井用地、邻近构造物等调查也至关重要。
An exemplary embodiment of the invention provides a method for producing an ultra thin wall metallic tube by cold working method with significant wall thickness reduction.
本发明提供一种用冷加工法制造超薄壁金属管的方法。
An exemplary embodiment of the invention provides a method for producing an ultra thin wall metallic tube by cold working method with significant wall thickness reduction.
本发明提供一种用冷加工法制造超薄壁金属管的方法。
应用推荐