The data on side clearance and open working clearance from the first to the fourth ring were provided.
提供了第一到第四道环的侧面间隙和工作开口间隙数据。
Take a saloon car for an example, it only consumes 16L water and the clearance working time of auto inflator is only 2-3 minutes.
以清洗一台小轿车为例，仅耗水16升，自动充气机间隙工作时间仅为2-3分钟。
The working principle and the constructional characteristics of a gear link mechanism for the clearance adjustment of pressure rollers in rolling machinery are discussed in detail.
详细论述了用于辊压机械中的齿轮连杆机构调整压辊间隙的工作原理及结构特性。
The Customs Clearance procedure will be finished within 3 working days when the documents of the above said flows are all ready.
以上全过程在单证齐全的情况下在3个工作日内完成清关程序。
The calculating method of the working orthogonal clearance of the flying cutting tool machining worm wheel in radial feeding way is put forward, and a calculating example is given out.
文中提出了考虑径向进给速度时飞刀左右侧刃工作后角的计算方法，实际算例验证了其正确性。
The experimental results show that the influence of clearance variation on flow structures and cascade performance is different at different working conditions.
试验结果表明，不同工况下间隙变化对流场结构的影响不同，因而对叶栅性能的影响规律也不同。
With different working pressure, the frame form of these series pump is also dissimilar, such as structure shown as in figure 5 and 6. Now introduce how to adjust the impeller clearance one by one.
该系列泵随着工作压力的不同，托架形式也不同，如图5、6图所示两种结构，现逐一介绍叶轮间隙的调整方法。
In this article, the motion of shots entered the clearance between impeller and control cage has been analyzed while blast wheel is working normally.
分析了机械进丸抛丸器在正常工作中定向套与分丸轮间隙中弹丸的运动过程。
The paper introduced the design of hardware and software of a kind of on-line monitoring device for disk brake shoe-clearance of hoister and its working principle.
文章介绍了一种提升机盘式制动器闸瓦间隙在线监测装置软、硬件的设计和工作原理。
The article discusses the influenced factors of rolling bearing's radial internal clearance, and fixes the optimal working radial internal clearance of offset printing cylinder's rolling bearing.
首先分析了影响滚动轴承径向游隙的因素，然后根据印刷要求，确定了胶印机滚筒滚动轴承的最佳工作游隙值，最后计算了不同印刷条件下该轴承的装配游隙。
During the ground test under different working conditions of the gas generator, the influences of the radial clearance and exhaust nozzle area were studied.
根据发射系统内弹道计算模型 ，针对燃气发生器喷喉面积对导弹发射动力的影响进行导弹运动参数、内弹道性能的计算与分析。
During the ground test under different working conditions of the gas generator, the influences of the radial clearance and exhaust nozzle area were studied.
根据发射系统内弹道计算模型 ，针对燃气发生器喷喉面积对导弹发射动力的影响进行导弹运动参数、内弹道性能的计算与分析。
应用推荐