If the body is damaged, replacement of the entire valve cartridge is recommended.
如果阀体损坏，则建议更换整个阀腔。
The actuator drives the shaft coupling and valve cartridge to adjust the material flow.
执行机构带动联轴器，阀芯动作，以调节物料流量。
After allowing the proper joint drying time, end connections may be joined to the valve cartridge.
—在经过适当的连接干燥时间后，端口连接件可能连接到阀腔上。
Check the valve if there is lumber inside the body, which will block the valve cartridge or damage the parts.
安装前请检查内腔有无杂物附着，否则会堵塞u型阀芯或损坏阀件。
To minimize downtime , it may be advisable to have a replacement valve cartridge ready to install in place of the one to be repaired.
为了减少停工时间，最好是准备好阀腔更换件，来安装在需要维修的部件的位置上。
Examine all parts and replace any damaged or worn components with new replacement parts. If the body is damaged, we recommend replacing the entire valve cartridge.
检查所有部件，用新的替换部件来更换任何损坏或磨损的部件。如果阀体损坏，我们建议更换整个阀腔。
The flow control valve is mainly made up of housing, body, sealing shim, liner bushing, valve cartridge, bearing, breather layer, aerator tank and transmission device etc.
流量控制阀主要有机座、阀体、密封垫、衬套、阀芯、轴承、透气层、充气槽及传动装置组成。
Concerning for the electrohydraulic system with digital valve and cartridge valve, this paper analyzes the intelligent time suboptimal control.
本文以数字阀、插装阀并联电液系统为例，分析了智能时间次优控制方法。
The press takes use of advanced two-way cartridge valve system and imported electric pump technology which can realize double closed loop control of pressure and flow rate.
液压系统采用了先进的二通插装阀系统、进口高性能的电子泵技术，实现了主缸压力与流量的双闭环控制；
Hydraulic systems use cartridge valve integrated control system, integrated cartridge valve control system has good sealing, flow capacity, small pressure loss characteristics etc.
液压系统选用插装阀集成控制系统，插装阀集成控制系统具有密封性好，通流能力大，压力损失小等特点。
This permits fouled valve replacement with a new body cartridge, which will fit the old union nuts.
这使得肮脏的阀门更换件可以配置新的阀体，并且可以与旧的管接螺母相配套。
A cartridge-type valve can be installed into an actuator port.
弹筒型阀可以安装到一个驱动器端口。
The Sanitary Cartridge Valve is a 316 stainless steel check valve for use in new or existing sanitary systems.
卫生级卡头阀门是用于新建或已有的卫生系统中的316不锈钢止回阀。
I plant the cartridge valve and reliable performance.
我厂生产的插装阀性能可靠。
This permits fouled valve replacement with a new body cartridge, which will fit the old union nuts. No change in piping length is required.
这使得人们可以用新的阀腔更换肮脏的阀门，新旧管接螺母能够互相配合，不需要改变管道长度。
From fluid flow momentum theory the basic equation of flow dynamic forces in the spool closing process is derived, and the spool dynamic equation of the two-way cartridge valve is established.
本文根据流体动量理论导出了阀芯关闭过程中液动力的关系式，在此基础上建立了二通插装阀阀芯关闭运动方程。
The double(multiple)-train dump hydraulic system is the system now very extensively utilized in the cartridge valve industry.
双（多）车翻车机液压系统是目前插装阀工业应用较为集中的系统。
The paper USES spool valve system drawing equivalent to cartridge valve system drawing to design a typical hydraulic closed-circuit system consisting of two-way cartridge valve.
本文采用滑阀系统图等效成插装阀系统图的方法，设计出一种由二通插装阀组成的典型闭式系统。
The application of cartridge valves on valve' s hydraulic actuator, and problems were analyzed when using the cartridge valves.
介绍螺纹插装阀在阀门液压驱动装置中的应用及选型注意事项。
Hydraulic system adopts integrated cartridge valve control, flexible action, reliable, no leakage.
液压系统采用集成式插装阀控制，动作灵敏、可靠，无渗漏。
Hydraulic system adopts cartridge valve system with the features of act reliability, electro-hydraulic quick response and long usage life, as well as independent electronic system and PLC control.
液压系统采用插装阀集成系统，动作可靠，电液响应快，使用寿命长。
The hydraulic cartridge cone valve is chosen for the study of possibility to explore its effects of geometry parameters and boundary condition on flow field and cavitation of cone valve.
以插装型液压锥阀为研究对象，研究了几何结构参数及边界条件对锥阀流场及气穴现象的影响。
Thus, the True union design permits the replacement of a fouled valve with a new body cartridge, which will fit the old union nuts that are likely to be permanently attached to adjacent piping.
因此，这种TrueUnion结构使得人们可以用新的阀腔更换肮脏的阀门，新旧管接螺母能够互相配合，好像永久性连接着邻近的管道上。
Hydraulic control using integrated cartridge valve system, reliable operation, long service life, small hydraulic shock, reduce the connection pipeline and leak.
液压控制采用整体式插装阀集成系统，动作可靠，使用寿命长，液压冲击小，减少连接管路与泄漏点。
We adopt the integrated cartridge valve and programmable logic control system in driving and control. Thus the technical level of production has been raised.
我们在机器的传动和控制方面采用了二通插装阀和可编程序控制器系统，使生产的技术水平有了新的提高。
The existing hydraulic test bench can test experiments of general hydraulic components while as can't test special hydraulic components(such as cartridge valves and multi-way directional valve).
现有液压实验台可以做通用液压元件的实验，却不能满足特殊液压元件（如插装阀和多路换向阀）的测试。
It can be concluded that cavitation of hydraulic cartridge cone valve is reduced by increasing the opening stroke and the outlet pressure and changing the geometrical structure of valve spool.
研究表明：增大阀口开度，增大出口压力，并对阀芯结构进行修改后，插装型液压锥阀阀口气穴现象均可有效减弱。
According to the simulation results, the opening pressure for the hydraulic motor lifting side cartridge one-way relief valve should be more than 1.9 times of the pressure of the maximum stable side.
根据仿真分析结果，液压马达提升侧单向溢流安全阀开启压力应大于该侧最大稳定压力的1.9倍。
According to the simulation results, the opening pressure for the hydraulic motor lifting side cartridge one-way relief valve should be more than 1.9 times of the pressure of the maximum stable side.
根据仿真分析结果，液压马达提升侧单向溢流安全阀开启压力应大于该侧最大稳定压力的1.9倍。
应用推荐