We can also measure the ultimate tensile strength.
我们仍能测量出，极限抗拉限度。
The SPPT improves the ultimate tensile strength by 3.5%, and elongation to failure by 25.7% .
超塑预处理使合金抗拉强度提高不很明显，仅为3.5%，而塑性提高了25.7%。
And the breaking point is given there in the third column, and we call that the ultimate tensile strength.
断点在第三列，有举出，我们称之为，极限抗拉强度。
The ultimate tensile strength(UTS) both in transverse and longitudinal of pipe body showed the trend for rising.
母材纵向的屈服强度及其屈强比均有上升趋势；钢管母材横向和纵向抗拉强度都呈上升趋势。
SPPT makes the ultimate tensile strength and the plasticity of the alloy increased by 3.5% and 25.7% respectively.
经超塑性预处理后合金在保持较高塑性的同时也有较高的强度，比传统处理工艺在强度上提高3.5%，塑性提高25.7%。
So we're going to load it up to the point that it will break, and that allows us to measure the ultimate tensile strength.
我们将继续装物体,直到断裂点，这样我们就能测量到,极限抗拉强度的大小。
And the ultimate tensile strength and elongation of low frequency electromagnetic cast billets are greatly increased.
相对于常规直接水冷铸造，低频电磁铸造提高铸态拉伸强度极限和延伸率。
The hardness of weld region shows'less variation than base metal and the ultimate tensile strength of TMAZ is almost 20% improvement.
焊缝区的硬度值波动范围很小，抗拉强度比母材增加约20％。
The ultimate tensile strength and elongation of extrusion bar after forging process was much higher than that of the direct extrusion bar.
先锻后挤工艺棒材最终抗拉强度和断后延伸率高于直接挤压棒材。
Based on the ultimate tensile strength test and extension test under confining pressure, the characteristics of flexible concrete are studied.
通过极限抗拉强度试验和围压作用下的拉伸试验，研究了柔性混凝土的抗拉破坏特性。
The results indicate that the ultimate tensile strength of AM60B increases prominently with the increasing of RE, the yield strength and elongation are also improved.
结果表明，AM60B的抗拉强度随着RE的增加有显著提高，屈服强度、伸长率也有所提高。
The results show that the ultimate tensile strength and yield strength of the alloys rise but the total elongation decreases as the temperature of quench medium drops.
结果表明：随淬火介质温度的降低，淬火降温速率提高，合金的强度增加，塑性下降；
Yield strength and ultimate tensile strength, work hardening exponent and normal anisotropy of plastic strain ratio decrease but planner anisotropy of plastic strain ratio increases.
屈服强度、抗拉强度、加工硬化指数和塑性应变比厚向各向异性降低，塑性应变比平面各向异性增大；
The correlation between the compressive strength and axial tensile strength of RCC with placing joint and ultimate tensile strain of placing joint of RCC layers have been obtained.
通过试验研究给出有层面碾压混凝土抗压强度、面轴拉强度与层面极限拉伸值间相关关系。
The tensile strength of the ionomers increases and the ultimate elongation decreases with the increase of sulfonate content.
随着磺酸盐含量的增加，离聚体的拉伸强度增大，伸长率下降。
Considering the randomness of strength and deformation of concrete material, a mathematic approach of producing random variables series of concrete ultimate tensile strain is proposed.
针对混凝土构件材料强度和变形性质的随机性，采用数学方法提出构造混凝土极限拉应变数列的原理。
The axial tensile had greater influence on the ultimate strength of the dented riser as the depth was deeper.
凹陷深度越大，初始轴向拉伸力的存在对立管的影响越大。
The axial tensile had greater influence on the ultimate strength of the dented riser as the depth was deeper.
凹陷深度越大，初始轴向拉伸力的存在对立管的影响越大。
应用推荐