The paper mainly introduces the process control and states the main problems existing in trial manufacture and relevant measures.
本文着重介绍了Q195L钢的生产工艺过程控制,阐述了试制Q195L钢过程中出现的主要问题及相应的措施。
The trial manufacture and use of tank show that selected insulation structure and technical method can fully satisfy the needs of design.
通过槽车的试制和使用情况证明,所选择的绝热结构和工艺方法完全能满足设计要求。
It represents the trial manufacture of grade X80 pipelines steel hot rolled coil with characteristic of acicular ferrite at BaoSteel Mill.
简要介绍了宝钢试制的以针状铁素体组织为特征的X80级管线钢热轧板卷。
During the trial manufacture period of Marine CO 2 fire extinguishing system, we solved some difficult technical problems of parts in the system.
在船用二氧化碳灭火系统的试制过程中,我们解决了系统各部件上的一些技术难题。
This paper describes design transformation and trial manufacture of Noranda reactor imported and development and design of sealed hood necessary for the reactor;
叙述了引进的诺兰达炉转化设计、研制和与之相配套的密封烟罩的开发设计。
Internallypiloting chemical composition and reasonable technological line are established, which make success through one trial-manufacture.
我们通过制定内控化学成分及合理的工艺路线,使生产试制一次成功。
This method of manufacture evolved out of a long process of trial.
这种制造方法是在长期试验过程中逐步形成的。
The article introduces trial-manufacture of grouting steel-edged rubber water stop and its application.
介绍了可注浆式钢边橡胶止水带的试制及应用情况。
The main structure of JM-203 nailing machine is stated briefly, the pneumatical system is stressed and the technology improvement is analyzed during the trial-manufacture.
简述了JM- 203钉角机的主要结构,重点介绍了其气动系统,并分析试制过程中的技术改进情况。
Improved design of the old instrument shaft, made success through one trial-manufacture.
改进了仪表传动轴原设计,一次试制成功。
Rapid trial-manufacture technology of car body is a technique that a low volume body work of new car can be fabricated at high flexibility and speed, and at low cost.
汽车车身快速试制技术是柔性极高、最低成本地快速完成极小批量新车型车身的试制技术。
This method of manufacture evolved out of a long process of trial and error.
这种生产方法是经过长期的试验和失败获得的。
The application of re can not merely improve the accuracy of design and manufacture, but also shorten the trial period and cut down cost.
逆向工程的应用不但提高了产品设计和制造的精度,而且缩短了产品的试制周期,降低了生产成本。
This paper mainly talks about the process trial, study and manufacture of phenolic FRP products with the property of anti-static electricity used in coal mine.
本文主要介绍供煤矿井下需要的防静电酚醛玻璃钢制品的工艺试验、研究及生产。
From material selection, structure, calculation, manufacture and detection etc., the design and trial-manufacture of GY-82 superhigh pressure vessel are more comprehensively summarized in this paper.
本文从选材、结构、计算、制造及检测等方面对GY- 82型超高压容器的设计与试制工作进行了较全面的总结。
H. The trial-manufacture of new products, test a number of requirements;
新产品的试制、试验的若干要求;
Shaping of double curved face lamella has been hard nut to crack in manufacture trial work.
在汽车车身试制领域,双曲面薄板零件的成形一直是试制工作的难题。
The trial sample of the utility model is verified by experiment running, and the utility model has the advantages of stable performance, practicality, beautiful appearance and low manufacture cost.
本方案的试制样品经实验运行证明:它具有性能稳定、美观实用、制造成本低的特点。
The trial-product of an example gear processed indicates digitalization-precision and the process program could meet the need of manufacture and be economical and feasible.
经试制加工实例齿轮表明,齿形数字化精度和数控加工程序满足生产要求,且经济可行。
These subjects are all put into industry trial-manufacture or production. The mechanism research has bee...
这些课题大都转入工业试制或生产,机理研究亦有所突破。
Through the trial analysis, we studied high precise NC manufacture on PMAC, this paper provided the foundation for application of PMAC on high precise manufacture.
通过实验,研究分析了基于PMAC的高速精密磨削数控加工,为实现PMAC在高速精密加工中的应用打下基础。
Process parameters were determined through the trial production for the manufacture of cement clinker by using the sludge of Suzhou river.
通过工业试烧确定了利用苏州河底泥生产水泥熟料的工艺参数,并对熟料及其水泥的性能进行了分析。
Then the design check-up, main model establishment, NC machining simulation, program optimization are realized before the trial-manufacture of prototype model.
针对下料问题产生的数学模型过大和生产中的实际情况,笔者编写了杆件下料优化程序进行建模求解。
Then the design check-up, main model establishment, NC machining simulation, program optimization are realized before the trial-manufacture of prototype model.
针对下料问题产生的数学模型过大和生产中的实际情况,笔者编写了杆件下料优化程序进行建模求解。
应用推荐