A transformer-ratio arm bridge with three terminals is adopted as its measuring circuit to eliminate the influence of electrode edges and exterior interference.
相应地，它的测量电路采用具有三个输入端的变压器电桥，从而免除了电极边缘和外界干扰的影响。
A rectangular wave generating circuit has been designed with MOSFETs, half bridge driver chip LM27222 and gate drive transformer.
利用MOS管、半桥驱动芯片LM27222、栅极驱动变压器等器件，设计了变极性矩形波发生电路。
The method of design high frequency transformer in half bridge inverter circuit is introduced exampled in detail, besides temperature rise and power loss are discussed.
依据一个半桥逆变电路的实例详细介绍了高频变压器设计的一般方法和步骤，并讨论变压器损耗和温升问题。
The cause of the DC bias of the main transformer in the full bridge inverter has been analyzed.
分析了全桥逆变器功率变压器产生直流偏磁的机理；
Full bridge topology was used in the main circuit, IGBT was used as power switching device, and micro-crystal core was used in mid-frequency transformer.
其主电路采用全桥式拓扑结构，以IGBT管为功率开关器件，中频变压器使用微晶磁心。
UC3846 is used for PWM, pulse transformer driven by bridge can transfer signal and power for IGBT in main circuit, quick protection is necessary for short circuit often happen during brush plate.
本文采用UC 3846作为PWM发生器，桥式驱动的脉冲变压器既保证信号的传输，又保证足够功率驱动全桥逆变主电路。对于经常发生短路刷镀刷镀工艺，快速过电流保护非常必要。
For isolated-type symmetry half-bridge bidirectional converter with phase-shifted control, a simplified circuit under 4 modes using the primary windings of transformer as reference object is built.
以隔离型对称半桥双向变换器为对象，建立了以原边为参考的4种模式下的简化电路，提出了结合开关函数的状态空间平均模型的建立方法。
The modified types will not be equipped with commutation transformer and the three-phase alternating current power supply directly acquires DC voltage through bridge type rectifier.
改进型不配整流变压器，将三相交流电源直接由桥式整流获得直流电压。
The utility model relates to a high frequency radiation eliminating device for electronic transformer of neon lamps, which is composed of a bridge circuit which is composed of diodes and a capacitors.
霓虹灯电子变压器高频辐射消除装置由二极管组成桥式电路和电容组成。
MW DC arc furnace uses the current 2-transformer rectifier bridge thyristor controlled by adjusting the angle trigger to compose 24 pulse wave rectifier circuit.
MW直流电弧的电流控制采用2台整流变压器控制，通过调节晶闸管桥触发角构成24脉波整流电路。
By employing the circuit topology of full-bridge inverter, the IGBT and the amorphous transformer, the power circuit could be built.
在功率电路拓扑的设计上，采用全桥逆变结构，并使用IGBT和非晶态变压器作为主要器件。
This paper studies the influence of converter transformer D-bridge zero sequence circulating current on valve short circuit protection.
笔者研究了换流阀三角形侧零序环流对阀短路保护误动作的影响。
The design method and steps are demonstrated by designing a half-bridge Buck converter with a flat transformer. Flat transformers can be used in varied electrical products.
通过用扁平变压器设计半桥式变换器的实例，说明其设计方法和步骤，并对设计结果进行了分析。
A transformer ratio bridge verification apparatus is introduced in this paper.
变压比电桥检定装置是检定变压比电桥的专用检定装置。
Phase - shifted converter realizes zero - voltage - switching with the use of leakage inductor of the main transformer, however, the realization of ZVS for lagging bridge leg is difficult.
移相控制全桥变换器能够实现开关管的零电压开关，但滞后桥臂难度很大。
Phase shifted converter realizes zero voltage switching (ZVS) with the use of leakage inductance of the main transformer, however, the realization of ZVS for lagging bridge leg is difficult.
移相控制全桥变换器能够实现开关管的零电压开关，但滞后桥臂难度很大。
Phase shifted converter realizes zero voltage switching (ZVS) with the use of leakage inductance of the main transformer, however, the realization of ZVS for lagging bridge leg is difficult.
移相控制全桥变换器能够实现开关管的零电压开关，但滞后桥臂难度很大。
应用推荐