These bearings have a particularly high axial load carrying capacity and are used primarily as thrust bearings in rolling mill applications.
这些轴承有特别高的轴向负荷能力,主要用作轧钢机里的推力轴承。
Screw propeller theory is then used to calculate the axial thrust and to analyze factors that influence the thrust.
讨论了各种因素对轴向水推力的影响,包括各项推力系数的选取和修正。
Most bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.
大多数轴承都支承径向或轴向负荷的转轴。
Single-direction and double-direction angular contact thrust ball bearings (Figures 1.50 and 1.51) are used for machine tool spindles requiring rigid axial guidance.
单向和双向推力角接触球轴承(图1.50和1.51)都用机床主轴轴向刚性作为指导。
Practices demonstrate that blocking balance hole is a effective method to resolve the axial negative thrust of rotor.
实践证明,堵平衡孔是解决转子轴向负推力问题的一种行之有效的方法。
Repelling vanes shall be provided on the top shroud to expel solids and reduce axial thrust and pressure at the seal area.
在泵顶部应该配置排斥叶片,用于排出固体颗粒,减少轴向推力和密封区域的压力。
The higher the speed should not adopt thrust ball bearings available class bearings are subjected to purely axial load.
在转速较高不宜采用推力球轴承的情况下可用该类轴承承受纯轴向负荷。
The MSH range is designed for high pressure applications and the axial thrust is balanced by the combination of the drum and disc.
MSH系列产品作为针对高压应用的设计,轴向推力通过平衡室系统和圆盘一起进行平衡。
There are two bi-directional thrust bearing rolling bodies, each listed in only one direction of axial load.
有两列滚动体的双向推力滚动轴承,每列只在一个方向承受轴向负荷。
The alternate roller bearing in FAG bearing, can bear at the same time come from each direction loading like axial, thrust or momentum loading.
FAG轴承中的交叉滚子轴承,能同时承受来自各方向荷重(如轴向、推力或动量荷重等)。
Bearing a single row thrust ball bearings to the heart, which has at the same time to bear a greater bearing axial load and radial load capacity.
轴承采用了单列向心推力球轴承,这种轴承具有同时承受较大的轴向荷载和径向荷载的能力。
Combined needle roller bearings consist of a radial needle roller bearing combined with a thrust bearing and are consequently able to take up both radial and axial loads.
组合式滚针轴承是由一个向心滚针轴承和一个推力轴承相结合,因此能够承受径向和轴向负荷。
Metrical experimental studies on screw torque, axial thrust, barrel inwall pressure of twin screw pulping extruder (TSPE) were done.
对双螺杆磨浆机的螺杆扭矩、轴向推力和机筒压力进行了测量实验研究。
Checkhigh/low speed thrust bearing axial float clearances.
检查高/低速轴向推力轴承浮动许可。
This paper presents the key technical points in increasing the capacity of an industrial turbine, such as steam flow, rotor strength, axial thrust and auxiliary equipments.
具体阐述提高工业汽轮机能力需考虑的主要技术问题:蒸汽流量,转子强度,轴向推力及辅助设施。
Whole model of impeller clearance and labyrinth seal are built up, and the effect of seals with two sides of impeller to axial thrust is considered fully.
建立了叶轮间隙和迷宫密封的整体模型,并充分考虑了叶轮两侧密封对轴向推力的影响。
Thrust ball bearings are designed for supporting axial forces; they are employed where axial forces are too high to be transmitted by radial bearings.
推力球轴承是专为支持轴向力设计的,他们用于轴向力过高,可以由径向轴承传播(的地方)。
With an additional axial thrust bearing, both the thrust and radial bearings are preloaded individually.
由于增加了一套轴向止推轴承,所有的推力和向心轴承均被分别预加载。
The tapered roller bearing replaces axial thrust ball bearing.
采用圆锥滚子轴承取代现有的轴向推力球轴承。
The axial overload is the main factor which causes work roll bearings and back-up thrust bearings of four-high mill invalid.
四辊轧机工作辊轴承和支承辊止推轴承失效的主要原因是它们在工作中所受的轴向载荷过大。
YRT series cylindrical roller and thrust needle roller combined bearings, with high rotation accuracy, can support heavier radial loads, double direction axial load and inclined torque, etc.
圆柱滚子和推力滚针组合轴承yrt系列具有旋转精度高、可承受较大的径向载荷和双向轴向载荷以及大的倾覆力矩等特点。
This article analysis the major reasons that lead an axial negative thrust in unit 3, introduce the method of remove axial negative thrust with block the balance hole.
通过计算,分析了3号汽轮机轴向负推力产生的主要原因,介绍了堵平衡孔消除轴向负推力的方法。
First, an expert system of fault diagnosis is set up by summarizing symptoms and their direct reasons for axial displacement fault and by combining them to the tilting pad thrust bearing performance.
首先总结了轴位移故障的特征和导致故障的直接原因,将它们和可倾瓦止推轴承的性能相结合,组成一故障诊断专家系统。
This paper aims at the high thrust pad temperature and abnormal axial displacement problem during the start-up course of 600 MW Supercritical Units.
针对600 MW机组启动过程中推力瓦温度高及轴向位移范围超常的问题,从形成原理及现场安装两方面加以分析,并提出处理策略。
Thrust ball bearings are designed to handle axial loads only.
推力球轴承的设计处理轴向负荷只。
The thrust bearings are capable only to sustain the axial loads, with low limit speed. They have two stress modes, I. E. One-way thrust and two-way thrust.
推力轴承只能承受轴向负荷,极限转速低。有单向推力和双向推力两种受力方式。
It can turn the axial thrust on the whole pipe.
在工作是可以反轴向推力传递至整个管道。
Single thrust ball bearing can be subject to the axial load from single direction.
单向推力球轴承可承受单一方向的轴向载荷。
Using of impulse section blade ensured its flow capacity with the axial thrust almost unchanged.
在保持轴向推力几乎不变的情况下,选用冲动式叶片保证了叶片有较好的通流能力。
Since the gear reducer is working with load, attention shall be paid to the temperature increase of axial cone bearing and sliding thrust bearing oil sump.
因为减速机此时已经是带负荷运转,所以应特别注意输入轴锥轴承的温升和滑动推力轴承油池的温升有无异常现象等。
应用推荐