The outside diameter, outer ring width and shaft seat diameter are identical to the dimensions of the standard spherical roller bearings range.
外部直径,外圈的宽度和轴座直径相同的尺寸标准的球面滚子轴承范围。
Valve drive shaft connected with the platform in line with the ISO5211 standard.
阀门轴端与驱动器的连接平台符合ISO 5211标准。
The shaft shall be cadmium-plated steel alloy or 316 stainless steel as standard equipment. Optional shaft materials shall be available on request, i. e. , titanium, stainless steel, etc.
阀杆应该是以镀镉钢合金或316不锈钢作为标准配置。备选的阀杆材料可以根据要求提供,例如,钛,不锈钢,等等。
If the drive shaft wear mild, just press the old bush changed after standard size bushing, fit clearance can be restored to allow range.
若主动轴磨损轻微,只需压出旧衬套后换上标准尺寸的衬套,配合间隙便可恢复到允许范围。
OSHA shaft and belt guarding is standard for increased safety.
标准的O SHA轴和传动皮带,提高运行安全性。
Extremely low cost. Standard high-precision ground spindle. Standard flat mounting arrangement. High overhung load capacity input shaft.
价格低廉,精密钻孔轴,平坦安装,悬臂式负载能力输入轴。
We adopted the precision cold drawn, honing and polishing to manufacture the precision Slender Shaft (Piston Rod), every technical target is over the national standard.
我公司专业生产精密细长轴(活塞杆)采用精密冷拔、精磨和高精度抛光的先进工艺制造,各项技术指标均符合并超过国家标准。
Single units are suitable for standard linear movements or where there is a severe shaft deflection.
单单位适合标准线性运动或那里是一个严重的轴偏转。
Lift the standard section by the self-install suspension shaft, and install it on the guiding track framework, and connect by the screw.
用自装吊杆吊起标准节,装到导轨架上,并用螺栓联接紧固。
A shaft end pump should be included in the standard installation. The assembly space should be considered at site. Shall the installation not meet the requirement, please contact with the supplier.
标准配置含轴端泵,现场应预留安装空间,若不能满足安装要求,请与厂家联系。
OSHA shaft and belt guarding are standard for increased safety.
标准的OSHA轴和皮带安全罩使增加了运行安全性。
Mixers are furnished with standard ANSI flanges with shaft seals for use on closed vessels.
搅拌机是配有标准的ANSI法兰与轴密封件用于封闭容器。
Three configurations are available - standard belt drive, jack shaft drive or direct drive.
共有三种结构可供选择—标准皮带驱动、传动轴驱动、或直接驱动。
Lift the 3 shaft adhered to wall to the suitable height, firstly, connect the shaft with one end of the standard section, then install on the connection plate of foundation bolt.
将三根附墙杆起吊到适当高度,首先用销轴将杆与标准节一端连接,然后安装到地脚螺栓连接板上。
This, combined with its open architecture and standard off-the-shelf products, helps provide improved usability and support over traditional line shaft drive control.
结合其开放式构架和标准原料产品,这样就帮助提供改善了的可用性而且支持传统的动力轴驱动控制。
The Nut Bracket is standardized for the standard Ball Screw assembly provided with finished shaft ends. It is designed to be secured directly on the table with bolts.
螺母支座是轴端、成品已被标准化了的滚珠螺杆标准规格品的螺母支座,其构造是用螺丝直接固定在工作台上。
PBPBGDL pump equipped with the company's B5 standard shielded motor shaft, a high degree of general-purpose, repair and maintenance is extremely convenient.
PBPBGDL型泵配备了本公司生产的B5标准轴屏蔽电机,通用程度高,检修维护时极为方便。
The worm and worm among plane within the modulus and pressure Angle, namely the worm gear were equivalent modulus is equal to the end of the worm shaft side modulus and for standard;
中间平面内蜗杆与蜗轮的模数和压力角分别相等,即蜗轮的端面模数等于蜗杆的轴面模数且为标准值;
Plastic implants nuts, riveted fasteners, rivets, connecting shaft and other standard fasteners and non-standard fasteners.
塑胶埋植螺母、压铆紧固件、铆钉、连接轴等标准件和非标紧固件。
Instrumentation parts, bolts, nuts, forging shaft, regulation pole, non-standard, American standard, British standard, etc.
仪表件、螺栓、螺帽、锻造轴、调节杆、非标、美标、英标等。
In the paper, the research on the quality of rolled stepped shaft for overcoming geometrical limitation and standard design of 3-roll cross wedge rolling mill is reported.
对三辊楔横轧轧件质量、克服几何限制条件措施及轧机定型设计等进行了研究。
Our major products are including Rollers, Rivets, Shaft Pins and other non-standard high strength Screws and Bolts which are widely used in auto seats, door lock and pipeline system.
公司的主要产品为汽车用机械加工零部件,如座椅、门锁、管路中的罗拉、铆钉、轴销类零件和非标高强度螺钉和螺栓。
Our major products are including Rollers, Rivets, Shaft Pins and other non-standard high strength Screws and Bolts which are widely used in auto seats, door lock and pipeline system.
公司的主要产品为汽车用机械加工零部件,如座椅、门锁、管路中的罗拉、铆钉、轴销类零件和非标高强度螺钉和螺栓。
应用推荐