The speed ratio is the ratio of the shaft transmission to the first digit wheel transmission.
速比配置数是出轴与头位字轮传动比。
Suitable for electronic shaft transmission use printer what would be the mainstream in the future.
适用于今后为主流的电子轴传动用印刷机。
Shows high magnetization effect of magnetic iron when magnetic particle coil not conductive, torque transmission shaft transmission from not in driven shaft.
显示高磁化效应的磁性铁粒子当磁性线圈不导电时，转矩不会从传动轴传导于从动轴。
Due to the different motorcycle models, motorcycle two way transmission belt transmission, chain drive and three kinds of universal joint drive shaft transmission.
由于摩托车机型的不同，摩托车二级传动方式有皮带传动、链传动和万向节轴传动三种传动方式。
Due to the different motorcycle models, motorcycle two transmission methods are belt drive, chain drive, and three kinds of universal joint drive shaft transmission mode.
由于摩托车机型的不同，摩托车二级传动方式有皮带传动、链传动和万向节轴传动三种传动方式。
In contrast, in the outstretched shaft type clutch or brake, magnetic coil and transmission between units have small desert land idle, so demand greater magnetized force.
相反，在伸出轴式离合器或制动器，磁性线圈与传动单元之间有小旷地空闲，所以需求较大的磁化力。
This locks the engine to the transmission input shaft, causing them to spin at the same speed.
这样使发动机和传动系输入油可靠地接合，使它们以相同的转速运转。
The rotating action of the pump against the fluid and the action of the fluid against the turbine turn the transmission input shaft.
泵轮的旋转作用冲击液体，液体的作用推动涡轮旋转变速器输入轴。
The third case is due to the deformation of the transmission shaft caused by the imbalance, the general situation in the chassis collision over the car.
第三种情况是因为传动轴变形不平衡引起，一般这种情况出现在底盘碰撞过的车比较多。
Drive shaft a drive shaft and universal joints connect the transmission to the rear drive axle on most rear-wheel-drive vehicles.
传动轴在大多数后轮驱动的车辆中主要是靠传动轴和万向节连结着变速箱与后轮驱动桥。
Was built in 1988, is the production of automotive transmission , transmission gear and various professional shaft manufacturers.
浙江鸿来机械有限公司建于1988年，是生产汽车变速器、各种变速器齿轮及轴的专业厂家。
The design of the main drive system mainly bases on the torque moment of transmission shaft.
传动扭矩是矫直机主传动系统设计的主要依据。
Our company specializing in the production of automobile transmission: synchronous, gear shaft.
我公司专业生产汽车变速箱：同步器、齿轮、轴。
Its input axis and transmission gearbox's output shaft with the rotary transmission device connection.
其输入轴与变速器的输出轴用万向传动装置连接。
These parts include the clutch, the transmission, the drive shaft, and the final drive assembly.
这些部件包括离合器、变速器、传动轴和后桥总成。
Rotary motion of the transmission main shaft carries through the propeller shaft to the differential, causing the rear wheels to rotate.
变速器主轴的旋转运动通过传动轴传递到差速器上，使后车轮转动。
Place Taper - lock Bushing and Timing Belt Pulley on the transmission shaft.
将锥面紧固套与同步带轮装在传动轮上。
He illustrates that torque on intermediate support and transmission output shaft is related to the arrangement of intermediate support, and measures to keep them in good condition.
笔者根据汽车传动轴的布置形式，对传动轴的中间支承和变速器输出轴的受力特性给予分析。
Drawworks adopts single shaft gear transmission structure, which is simple and reliable.
绞车为单轴齿轮传动结构，传动结构简单、可靠。
The problems of the signal transmission in a shaft have not been solved because the transmission environment is very bad.
煤矿立井井筒的信号传输，由于其传输环境特殊，一直没有很好地解决。
Then, the system constitution, drive form, and control strategy of shaft-less transmission were analyzed and studied.
无轴传动为印刷设备传动系统提供了新的解决方案。
C. shaft coupling on the transmission shaft should be connected with rubber shaft coupling on gear reducer.
传动轴上的联轴器必须与齿轮减速箱上的橡胶联轴器相联接。
Sparated Bearing block for main transmission shaft Easy for maintenance and fix.
主传动轴承座可分拆结构，方便安装及维护。
The testing method using fall size substance specimens is introduced for transmission shaft, oil well pipe, train pothook, cover of sewer well.
介绍了传动轴、油井管、火车挂钩、窨井盖等全尺寸实体试件试验方法与工程实际应用情况。
The drive system on Model TCM870 loader features three-element torque converter and counter shaft, constant mesh, power-shift transmission.
TCM 870装载机传动系统，采用三元件液力变矩器和定轴式常啮合动力换档变速器。
The metallurgical structure and fracture morphology on gear transmission shaft of 45 steel were analyzed by means of optical microscope and scanning electron microscope.
采用光学显微镜、扫描电镜等分析手段，对45钢大齿轮传动轴断裂表面的金相组织、断口形貌进行了分析和检测。
The metallurgical structure and fracture morphology on gear transmission shaft of 45 steel were analyzed by means of optical microscope and scanning electron microscope.
采用光学显微镜、扫描电镜等分析手段，对45钢大齿轮传动轴断裂表面的金相组织、断口形貌进行了分析和检测。
应用推荐