The larger the shaft deformation, the more serious the vibration.
轴变型越大，振动也越严重。
The author ascribed the shaft deformation and failure to a complex contribution of three factors, namely geological weak position, negative friction, and horizontal loading.
在竖井变形破坏的工程调查和总结研究的基础上，提出了徐淮地区竖井变形破坏“三因素综合破坏”观点。
Some expression patterns of control and state variables of shaft deformation, which give us a significant guidance of effective dealing with shaft damage have been presented.
给出了井筒变形的控制变量与状态变量表达式；对有效地治理损害的井筒具有重大指导作用。
Some forecast and application viaduct pier shaft deformation will not only guide for the construction, but also make the bridge structure more reasonably and prolong its using life.
因此对其变形量进行预估并加以运用，一方面可以指导施工，另一方面又可以使桥梁结构更加合理，延长使用期限。
Multidisciplinary coupling analysis on dynamics, tribology, strength and stiffness for a shaft-bearing system was studied herein, considering misalignment caused by shaft deformation on variable load.
轴倾斜使得轴-轴承系统的动力学响应、润滑性能以及轴颈表面动应力发生改变。
Rotational deformation of the shaft will produce maximum deflection.
转动的泵轴会弯曲变形，产生最大挠度。
The paper has studied straightening stress and residual deformation of circular shaft by using elastic - plastic theory, deueloped calculation formula of straightening loud in given deflection error.
从弹塑性理论出发以圆截面轴为例对校正应力与残余变形进行了分析研究，提出了在给定弯曲误差下的校正载荷的计算公式。
The third case is due to the deformation of the transmission shaft caused by the imbalance, the general situation in the chassis collision over the car.
第三种情况是因为传动轴变形不平衡引起，一般这种情况出现在底盘碰撞过的车比较多。
However to the large deformation shaft without crack, general predictive theory has been applied to built up the multi-steps straightening stroke predictive algorithm.
针对单弧度弯曲大变形无裂纹轴校直问题，根据广义预测控制理论，建立了多步校直行程预测算法。
Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.
某舰的螺旋桨尾轴长期处在恒定载荷作用下，虽然尾轴应力在弹性极限范围内，但是尾轴局部还是很容易发生微量的塑性变形。
In the process of rolling, the movement of rolling sets decide the rolling pressure, the deformation of the spindly shaft and consequently the rolling quality.
在滚压加工工艺中，滚压套的压下量大小决定了滚压力的大小并决定了细长轴表面发生弹塑性变形的状况，从而决定了细长轴的加工质量。
During the experiment on mechanics of materials, a problem of solid circular shaft in torsion testing for large deformation remains unsolved.
目前在材料力学实验中的圆轴扭转大变形问题尚未解决。
Due to the complex structure of crank shaft, its stiffness varies in different angles, which results in the varying forced deformation error.
曲轴的结构复杂，不同角度下的刚度不同，受力变形也不相同。
The shortcomings of this method is easy to welding deformation of the chain of boxes, at both ends of the coaxial shaft tolerance and lack of support strength.
此法缺点是焊接后链条箱易变形、两端轴的同轴度超差以及支撑强度不够。
The problems of deformation for shaft lining are investigated under arbitrary axisymmetric normal loads and tangential loads with end loads.
对有限长立井井壁在任意轴对称的法向、切向以及端面荷载的共同作用下的变形问题作了分析研究。
The material of frame and shaft head is imported. It's of high strength that can bear high pressure. It's never deformation.
机身及轴头均采用进口材料制作，强度高，能承受超高的压力，绝不变形。
The effects of shaft geometry, load level, concrete elastoplasticity and shaft resistance softening on bearing and deformation characteristic of LDSLP were studied by using this model.
采用该分析模型，分析了桩身几何参数、桩顶荷载水平、混凝土弹塑性和桩侧阻软化效应对大直径超长单桩承载变形性状的影响。
Cold beating lead screw plays the role of high-speed relative motion in the way of high-speed blowing shaft blanks, so that local plastic deformation forms a non-chip metal forming technique.
丝杠冷打是在工具和丝杠高速相对运动中，以高速断续的方式击打丝杠轴坯，使丝杆轴坯局部塑性变形形成丝杠螺纹的一种无屑塑性成形技术。
The deformation feature of deep shaft coal roadway is analyzed, and the reason for many kinds of support failures is studied.
分析深井煤层巷道围岩变形特征和支护失效的原因，提出此类巷道的内外结构耦合平衡支护原理。
Results Obtained the distortion deformation, stress nephogram, section stress of femur neck and upside of femoral shaft of the femur under the bending moment and compressive load.
结果得出了在弯压复合荷载下股骨的变形、应力云图、股骨颈和股骨干上端的截面应力。
Some main processing parameters are briefly introduced, such as speed of main shaft, feed rate, shape of spinning wheel, deformation rate of each step and structure of template.
对主要工艺参数如主轴转速、进给率、旋轮形状、道次变形率、模板形式等作了简要介绍。
It is a technical difficulty to control the deformation and the stress condition of the structure of large-scale shield shaft in over-river shield tunnel project.
控制超大盾构工作井的变形和结构受力状态是跨江跨海盾构隧道工程设计和施工的技术难点。
The cross wedge rolling deformation process of shaft parts with eccentric section was simulated with three-dimension finite element soft LS-DYNA by using elastic-plastic finite element method.
利用三维弹塑性有限元软件L S- DY NA对一种典型偏心轴类零件楔横轧成形进行了数值模拟，分析了其成形过程、应力应变场分布及工艺特点。
Finally, combined with an engineering example, the effect of different soil modulus on the internal forces and deformation along pile shaft is discussed.
最后，结合工程实例讨论了不同桩侧土体变形模量分布模式对桩身内力变形的影响规律。
An introduction is made in the paper of the method for deformation survey of disposal shaft wall and cage guide in No. 5 Mine of Yangquan Mining Group.
文中介绍了阳煤集团五矿排矸井井壁及罐道变形的测量方法。
An introduction is made in the paper of the method for deformation survey of disposal shaft wall and cage guide in No. 5 Mine of Yangquan Mining Group.
文中介绍了阳煤集团五矿排矸井井壁及罐道变形的测量方法。
应用推荐