Automatically control the cutting speed to avoid over-burning according to plate thickness. Possible to edge cutting, offset cutting, to avoid wasting of meal sheet caused by calculation errors.
根据钢板厚度，在转角处可自动限速，有效防止过烧。支持边缘切割、偏移切割，对较厚的钢板可减少预热时间，并可避免因排料计算错误而造成的板材浪费。
In the thesis, a non-contact measurement technology by combining an eddy current displacement sensor with a sonic thickness sensor was put forward to measure timely real plate gap of refiner.
本文对采用电涡流传感器和超声波测厚仪组合实时非接触测量磨盘真实间隙的设计方案进行了研究和探讨。
The thickness of the steel plate handled by this roller mill (shear machine) is 25millimeters.
这台滚压机(剪切机)添工的钢板厚度可达25毫米。
A variable wall thickness scroll plate constituted by general scroll profiles based on functional theory was taken as the study object.
以基于泛函通用涡旋型线构成的变壁厚涡旋盘为研究对象，建立了以能效比为目标函数的结构参数优化模型。
The thickness of the steel plate handled by this roller mill( shear machine) is25 millimeters.
这台滚压机（切机）工的钢板厚度可达25毫米。
The failure mechanism of interaction process between the foundation and cavity and, the effect of every factor on safe thickness of top plate are studied by FEM simulation.
采用有限单元数值模拟法研究了基础与洞室相互作用下的破坏机制 ，以及各影响因素对浅埋地下洞室安全顶板厚度的影响及相关变化规律。
The static method is used to measure the thickness of steel plate by means of slow neutron beam.
利用慢中子束对钢板厚度的静态测量方法进行了研究。
Plating method, Cylinder or MATTHEWS, depends on customer request, printing plate thickness could be appointed by customer.
圆柱卷版方式或欧式MATTHEWS装版方式，可依客户要求制作。
The weldability of AZ31 magnesium plate by He-Ar mixed gas tig welding was investigated. The welding process parameters for AZ31 plate with a 3 mm thickness were optimized.
探讨氦-氩混合气体保护下tig焊接az31镁合金板的可焊性，对其焊接工艺参数进行确定。
The steel plate 'performance in the lamellar tearing resistance aspect can be assessed by reduction in area when doing tension test of through-thickness.
钢板的抗层状撕裂性能采用厚度方向拉力试验的断面收缩率来评定。
The thickness of the steel plate handled by this roller mill (shear machine) is 25 millimeters.
这台滚压机(切机)工的钢板厚度可达25毫米。
The bearing capacity of the connections is improved by adjusting plate thickness and arranging stiffeners.
通过调整节点域板件的角度，改善其构造的合理性。
Besides, Suggestions for seismic design have been presented as well to improve the seismic behavior of end-plate connections by adopting the end-plate with moderate thickness and large bolts.
对提高端板连接节点的抗震性能提出了宜采用大直径螺栓、中等厚度端板的设计建议。
Thickness of the aluminium plate is measured with laser ultrasounds. It tallies quite well with the real value. The minimum displacement which can be detected by the system is also meas...
用激光超声测得铝块厚度与实际值很好地吻合，同时测出了系统的最小可探测位移。
Thickness of the aluminium plate is measured with laser ultrasounds. It tallies quite well with the real value. The minimum displacement which can be detected by the system is also meas...
用激光超声测得铝块厚度与实际值很好地吻合，同时测出了系统的最小可探测位移。
应用推荐