The invention discloses a manufacturing method of piston connecting rod parts, which can manufacture a piston of which the strength satisfies requirements with common panels.
本发明公开了一种活塞连杆部件的制造方法,使得用普通板材即可制造强度可满足要求的活塞。
The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.
连杆的一端与曲轴的连杆轴颈相连,另一端通过活塞销与活塞相连。
The piston may be connected to the upper end of the connecting rod either directly (trunk piston type), or indirectly (crosshead type).
活塞与连杆上端的连接,既可以是直接连接(筒状活塞式),也可以是间接连接(十字头式)。
The connecting rod carries the power thrusts from the piston to the crankpin. At the same time, the rod is in eccentric motion.
连杆的作用是将活塞承受的压力传给连杆轴颈。同时,连杆做偏心运动。
The connecting rod is attached to the piston by the piston pin.
连杆与活塞的连接是采用活塞销。
The piston pinhole in the piston also serves as a bearing for the piston pin, which is used to connect the connecting rod.
在活塞中活塞销孔也同样为活塞销形支承面,其作用为连接连杆。
The connecting rod links its large end to the crankshaft and its small end to the piston.
连杆的大头与曲轴连接,小头与活塞链接。
Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn.
活塞通过连杆和轴连接,使得气体带动轴旋转半圈。
The connecting rod little end is connected to the piston pin.
连杆小头连接着活塞销。
Have studied the natural vibration characteristic of the piston - connecting rod - crankshaft while keeping in touch with the condition each other adopting systematic methods.
采用系统的方法研究了活塞-连杆-曲轴三者在相互接触条件时,在不同转角下的固有振动特性。
The engine piston, connecting rod and crankshaft convert this pressureinto motion for moving the car and operating other systems.
发动机活塞、连杆和曲轴将这种压力转换为运动,从而推动汽车行进并使其他系统运行。
The verification of assembly modeling system by taking example for piston and connecting rod indicates the feasibility and validity of the system.
本文原型系统通过发动机部件活塞连杆装配体加以验证,表明了系统的可行性和有效性。
In trunk-piston engines, a horizontal pin within the piston is encircled by the upper end of the connecting rod. This by far the most common construction.
在筒状活塞式的发动机中,活塞与连杆上端通过一个水平销子连接。这是最常见的一种结构。
Aemission spectrometer, micro-hardometer, optical microscope and scanning electron microscope were used to analyze the reason of crack on connecting rod unit assembly for piston of car engine.
采用直读光谱仪、显微硬度机、光学显微镜和扫描电子显微镜等分析手段,对失效的汽车发动机活塞连杆总成断裂原因进行了分析。
This paper describes the substitution of piston and connecting rod assembles in domestic 492q model engines for ones in VOLGA-24 passenger cars.
介绍了以国产492Q型发动机活塞连秆组件代用伏尔加24型轿车活塞连杆组件的方法。
The connecting rod transmits the up-and-down motion of the piston to the crankshaft, which changes it into rotary motion .
那连接竿送活塞的上上下下运动到机桥,将它换成旋转的运动。
Upper and lower ends of the hydro-cylinder identity are installed upper pressure board and down pressure board, which has piston rod and connecting stick.
复合式弯辊液压缸缸体的上、下端分别装有上压板和下压板组成油缸,里面装有活塞杆和连接杆。
Main product: Tongyi engine oil, Zhengyang crankshaft, Zhenghe chain, Nanping piston ring, Mingyang connecting rod piston ring, Rushan Gaogui aluminum piston ring, Haijiu battery, Green battery.
主营:统一机油、罡阳曲轴、征和链条、南平活塞环、明扬连杆活塞环、乳山高硅名铝活塞、海久电池、格林电池。
The connecting rod is attached to the crankshaft at one end (big end) and to the piston at the other end (small end).
连杆一端(大头)与曲轴相连,另一端(小头)和活塞配合。
For example, in reciprocating piston compressor and power machinery, to connect the piston with connecting rod and crank.
例如在往复活塞式动力机械和压缩机中,用连杆来连接活塞与曲柄。
The FEM for the assembly parts of piston, gudgeon pin and small-end of connecting rod is constructed to investigate a diesel engine piston with an oscillating-oil-cooling channel.
针对某增压柴油机振荡冷却油腔活塞的非对称结构,建立全活塞活塞销连杆小头的有限元模型;提出了振荡冷却油腔的第三类热边界条件的数学描述并进行了验证;
After the piston-and-connecting-rod assemblies have been removed from the engine and the pistons and rods separated, the rings should be removed from the piston...
先将活塞及连杆组件从发动机上拆下再把活塞与连杆分开之后,即可将活塞环从活塞上取下。
After the piston-and-connecting-rod assemblies have been removed from the engine and the pistons and rods separated, the rings should be removed from the piston...
先将活塞及连杆组件从发动机上拆下再把活塞与连杆分开之后,即可将活塞环从活塞上取下。
应用推荐