没有网络引导服务器。
The last type of boot is the network boot option.
第三种启动类型是网络启动选项。
For SLES 9, the network boot image file is install.
对于SLES9，网络引导映像文件是install。
Copy the Enterprise Linux network boot images to the TFTP server root directory.
将EnterpriseLinux网络引导映像复制到TFTP服务器根目录。
The first installation CD contains the network boot image for the Linux distribution.
第一张安装CD包含Linux发行版的网络引导映像。
For this step, each node must be booted using the PXE network boot option in the BIOS.
对于这个步骤，每个节点都必须在BIOS中使用PXE网络启动选项来启动。
(If you will need this option later, define the third boot device as Network BOOTP).
(如果您以后还需要这个选项，那么将第三引导设备定义为Network BOOTP)。
Million Ethernet interfaces support not only Ethernet access but also network boot.
两个百兆网口不仅可以高速入网，还支持网络远程启动。
In this step, you configure the DHCP server to provide network boot information to new LPARs.
在这一步骤中，需要配置DHCP服务器以为新的LPAR提供网络引导信息。
Your network administrator must have added your machine to the list of allowed clients for network boot.
您的网络管理员必须已将您的机器添加到网络引导的允许客户端列表中。
To set up the network boot, you need both the DHCP server and TFTP server loaded on a server in the network.
要设置网络引导，必须将DHCP服务器和TFTP 服务器装载到网络中的服务器。
One system I own spends about five seconds initializing network boot parameters even if network booting is disabled.
我的一个系统就会花大约5秒钟的时间来初始化网络引导参数，即使在禁用了网络引导功能的情况下也是如此。
This enables a PXE server to know (at boot time) the exact architecture of the client from the first network boot packet.
这使PXE服务器能够知道(在启动时)从第一个网络引导数据包的客户端的确切的体系结构。
The end goal is to enable a client computer to boot from the network and receive a network boot program (NBP) from a server.
最终目标是使客户端计算机从网络进行引导，并从服务器接收网络引导程序 （NBP）。
As mentioned, to boot via the network Adaptor, your network administrator must have added your machine to the list of allowed clients for network boot.
如上所述，要通过网络适配器进行引导，您的网络管理员必须已将您的机器添加到网络引导的允许客户端列表中。
This low-level area of the hardware allows you to reset a hung system, boot from a specific device (like a CD or a network boot), or get into single-user mode.
硬件的这个低级区域允许您从特定的设备（如CD或网络）启动重新设置挂起的系统，或允许您进入单用户模式。
The BIOS can perform a variety of hardware scans looking for bootable devices, and on some systems the BIOS can even try to perform a network boot over Ethernet.
BIOS可以执行各种硬件扫描，从而寻找可引导的设备，在某些系统上，BIOS甚至可以执行通过以太网进行的网络引导。
This paper presents the design thoughts of Network Bootstrap Program and introduces the implementation of its key modules such as boot process, virtual disk and image file.
论文详细陈述了网络引导程序的设计思路，对其中涉及的引导过程，虚拟磁盘和映像文件等关键技术实现，予以详细介绍。
Note that if your project does not require a hard disk, as is the case for many thin clients, it must boot via CD, USB, or Preboot eXecution Environment (pxe-that is, network boot).
注意，如果您的项目不需要硬盘(许多瘦客户机就属于这种情况)，则它必须通过CD、u SB或Preboot eXecutionEnvironment (PXE—也就是网络)来启动。
A discover image is a type of boot image that you can use to install an operating system on a computer that is not capable of network booting using the Pre-Boot Execution Environment (PXE).
发现映像是网络的一种可用于不能引导使用预启动执行环境(PXE)的计算机上安装操作系统的启动映像。
You can rename the network boot image so that the network boot images for many Linux distributions can coexist, as long as they are the same as what is specified in the DHCP server configuration file.
可以改变网络引导映像的文件名，以便让许多Linux发行版的网络引导映像可以共存，只要文件名与DHCP服务器配置文件中指定的名称相同即可。
Each network adapter should be configured with a boot address and associated host name.
每个网络适配器应该配置一个引导地址和相关联的主机名。
Because you are not configuring this DHCP server to perform dynamic addressing, it will respond to the boot requests from your LPARs without interfering with normal DHCP operation on the network.
因为没有将这个DHCP服务器配置为动态寻址，所以它将响应来自LPAR的引导请求，并且不影响在网络上进行正常的DHCP操作。
Then you can boot a system over the network and have it unpack and flash the relevant firmware.
然后，可以通过网络启动一个系统，然后解开镜像，刷新相关固件。
This defines the boot IP addresses on the respective network adapters.
这在网络适配器上分别定义相应的引导IP地址。
You can use this command to tell the system to boot from CD, disk, the network, or other devices.
可以使用这个命令让系统从CD、磁盘、网络或其他设备引导。
You may normally boot from a hard drive, but you may sometimes need to boot from a floppy disk, a USB memory key, a CD or DVD, or a network.
您可能通常从硬盘驱动器引导，但有时可能需要从软盘、usb内存密匙、CD或DVD，或者网络引导。
通过网络进行引导。
Modify the example as necessary, then use it to power on an LPAR and attempt to network-boot it from a server in the network.
根据需求修改这个示例，然后在一个LPAR 上使用它，并尝试从网络中的服务器引导它。
A boot device can be a floppy disk, a CD-ROM, a partition on a hard disk, a device on the network, or even a USB flash memory stick.
引导设备可以是软盘、CD - ROM、硬盘上的某个分区、网络上的某个设备，甚至是usb闪存。
应用推荐