Among them the control system of hardware has introduced the peripheral circuit including main chip mainly, the module the signal gathers and the motor driving module.
其中硬件控制系统主要介绍了包括主芯片的外围电路，信号采集模块以及电机驱动模块。
The third chapter mainly introduces the hardware design of soft starter, including the main circuit, control circuit, drive circuit, and protect circuit and auxiliary switched power design.
第三章详细介绍了软起动控制器的硬件设计，包括主电路、控制电路、驱动保护回路和辅助开关电源电路的分析和设计。
At first, hardware circuit of the system has been designed, including minimum system of DSP, sampling pretreatment, dead zone formation, constant amplitude control and display circuit.
本文首先设计了系统的硬件电路，包括DSP的最小系统电路、采样预处理电路、输出信号死区形成电路、恒幅控制电路和显示电路。
Haredware circuit mainly including microcontroller interface circuit, electrical source and control circuit, measure circuit.
硬件电路主要包括：单片机接口电路，电源及控制电路，测量电路。
This paper studied control system with the center of SPCE061A MCU, including the drive and soft-start circuit of two power supply, the key and distance control of the cleaner.
以SPCE061A单片机位核心，研制了高效、适用的控制系统，包括两个电源的驱动、软启动、净化器的按键及遥控等电路。
The hardware of permanent magnet AC servo system is designed, including system power main circuit, system control circuit and auxiliary circuit.
设计了永磁交流伺服系统硬件电路，包括系统功率主电路、系统控制电路和辅助电路。
A hardware control system based on DSP TMS320F2808 was designed, including DSP base circuit, signal feedback circuit, drive circuit, wire driving circuit and protection circuit.
设计了以TMS320F 2808DSP为核心的硬件控制系统，包括DSP基本电路、信号反馈电路、驱动电路、送丝电路以及保护电路。
In this part, some points are presents in detail, including hardware choosing, unit circuit design, control principle and control algorithm.
论文对于器件的选型、各单元电路的设计、控制原理以及控制算法都进行了详尽的说明。
In this part, some points are presented in detail, including hardware choosing, unit circuit design, control principle and control algorithm.
论文对核心器件的选型，单元电路的设计，控制原理以及控制算法都进行了详尽的说明。
Experimentally, a linear tuning filter's set including a finished product narrowband thin-film interference filter and control circuit of stepping motor has been designed.
在实验方面，选用一个成品窄带滤光片，设计步进电机控制电路，实现了一个线性调谐光滤波器装置。
This paper introduces the design and implementation of ventilator control system based on FPGA including principle and electric circuit.
本文详细介绍了基于FPGA的呼吸机控制系统的设计和实现，包括原理和电路结构图。
Designs the plate cutter PLC control system including hardware electric circuit and software procedure.
设计出剪板机plc控制系统，包括硬件电路和软件程序。
This paper introduces in detail the design and implementation of ventilator SPONT control chip based on FPGA, including principle and electric circuit.
本文详细介绍了基于F PGA的呼吸机SPONT 模式控制芯片的设计和实现，包括原理和电路结构图。
The project also carried out system design, including: the overall cooling control system design, hardware design and selection, circuit design.
本课题还进行了系统设计，主要包括：冷却控制系统整体设计、硬件设计及选型、电路设计。
In addition, the structure increase a functional circuit including the comparator and logic control modules to ensure the reference source working perfectly.
设计中还增加了功能电路包括比较器及一些逻辑控制模块，保证基准源电源供电切换顺利；
Power electronics including power electronics, inverter circuit and control circuit of three parts, which is the basis for power electronic devices, power electronics converter technology is the core.
电力电子技术包括电力电子器件，变流电路和控制电路三个部分，其中电力电子器件是基础，变流技术是电力电子的核心。
Focus on the controller hardware system structure, Including signal regulate circuit, tripping control circuit and GPRS communication module circuit.
重点叙述了控制器的硬件系统构成，包括信号调理电路、脱扣控制电路和GPRS通信模块电路。
Then the circuit and program of on-board motion control system are designed according to the needs, including chief MCU circuit and motor control circuit.
其次，根据设计要求，进行底层运动控制系统硬件电路和软件程序的设计，主要包括了主控制器电路和电机控制电路。
This is a BLDC control procedures, including the circuit diagram.
这是一个BLDC的控制程序，包括有电路图。
Designed a temperature control circuit in the overall temperature control unit, mainly including temperature acquisition unit, control unit, trigger unit, power supply and other hardware circuits.
整体温控部分主要进行了温度采集单元，控制单元、触发单元，电源等硬件电路的设计。
It is applicable for control, monitoring circuit and protective circuit of rated voltage up to and including 450/750V, used in the anti-flaming location which requires environment protection.
用途Usage适用于使用交流额定电压450/750及以下控制、监控回路及保护线路等有一定环保要求的阻燃场合。
It is applicable for control, monitoring circuit and protective circuit of rated voltage up to and including 450/750V, used in the anti-flaming location which requires environment protection.
用途Usage适用于使用交流额定电压450/750及以下控制、监控回路及保护线路等有一定环保要求的阻燃场合。
应用推荐