Therefore, at the entrance to the air gun pressure measurement is very important.
因此，对喷枪空气入口处进行压力测量非常重要。
In short, according to the two gun pressure gauge readings, you can determine whether the leakage and blockage of the tube.
总之，根据两杆枪压力表读数的情况，可以判断出管束是否泄漏和堵塞。
Aiming at the difficult problems that encountered by the pressure Testing Device inside the gun pressure in the current test.
本文针对膛内压力测试装置在当今测试中遇到的问题。
The computing data indicates that because cartridge cases are thin walled cylinders, the emission stress and plastic deformation are high under gun pressure.
应用非线性有限元方法计算药筒的发射应力和抽壳力。
The pigment is introduced into the airbrushing gun and using low pressure the gun will pulverize the makeup on the surface of the skin.
将粉底颜料装入喷枪中，使用低压将粉碎后的粉底颜料喷到皮肤表面。
Once you make a call, the washer will come to your house on a tricycle, carrying a water tank, a water pipe, a high-pressure spray gun, cleaning agents and towels.
只要打个电话，洗车工就骑着三轮车，载着水箱、水管、高压喷枪、清洗剂、毛巾等洗车工具应约而来。
Now the plasma arc cutting machine part on gas pressure to control the flow, because when gun aperture, the gas control certain pressure and you control the flow.
现在的等离子弧切割机大多靠气体压力来控制流量，因为当枪体孔径一定时，控制了气体压力也就控制了流量。
At last, acquired conclusion is that band cut is not only in relation to gun bore wear and bore pressure, but also to length of heavy wear section.
最后得出结论：弹带削光不仅与内膛磨损量和膛压大小有关，还与严重磨损段的长度有关。
Because joined light molecular weight gas in Elctrothermal Chemical Gun, the pressure distribution in projectile base is improved and the projectile velocity enhanced.
由于该炮在电热化学炮的基础上加入轻质气体这一理想工质，因而能大大改善弹丸后部的压力分布，提高火炮弹丸的初速。
In this paper some problems, which exist in the peak pressure measurements under impulsive loading of explosion by the gun copper ingot, are discussed and an improved method is presented.
本文对目前用的炮用铜柱测量爆炸后脉冲载荷峰值压力方法中所存在的问题进行了论述，并提出了革新方法。
The main reasons to the rotary air pre-heater secondary combustion are related to unstable oil gun combustion, internal oil leakage and insufficient soot-blower steam pressure, etc.
锅炉回转式空气预热器发生二次燃烧的主要原因与油枪燃烧不稳定、内部有漏油和吹灰蒸汽压力不够等相关。
The pressure sensor used in under water gun, and the abnormal phenomenon in pressure measurement are introduced, the cause of abnormal phenomenon is analyzed in theory.
介绍了用于水下发射膛压测量的压力传感器，针对水下测压时有无充脂所出现的不同现象，以理论推导分析了产生此现象的原因。
This paper primarily introduces distinguishing features of in-bore mechanical environment of high chamber pressure gun and reguirments of "hard wire" technique for obtaining in-bore date.
本文主要介绍高膛压火炮膛内力学环境的特点及对膛内硬线传输技术的要求。
But because the chamber pressure of this gun is high, the deformation of the steel cartridge case is enlarged, and the extraction ratio cannot reach the standard.
但由于该炮膛压较高，使得钢质药筒的变形加大，不抽筒率超标严重。
Most of studies overlooked sleeve type ejection gun and the effect of pressure area changes, simultaneously the models of ejection gun were lack of extensity.
以往研究中对多级弹射筒和压力有效作用面的影响重视不足，并且所建模型通用性差。
The best second initiation time for gun-launched FAE was determined through the static explosive experiment and the change of pressure in exploding field.
通过设计战斗部静爆实验，依据爆炸场的压力变化确定了某型炮射云爆弹最佳二次起爆时间。
The charge utilization ratio is high for multi-point ignition tube experiments in a high-pressure gun, but the chamber pressure wave is high.
某高膛压火炮试验中发现多点点火方案的装药利用率较高，但膛内压力波较大。
Virtual spraying with high-pressure airless spraying gun at the above sites leads to thinner coating! that can not meet the process requirements.
使用高压无气喷枪喷涂导致上述部位虚喷，漆膜厚度没有达到工艺要求。
The model predicts the transient variations of gun chamber pressure, projectile motion and the decomposition rate of propellant.
模型可以预测发射过程中药室内压力、弹丸运动及工质的分解速率的瞬时变化。
The hydraulic pressure clay gun is smelts iron one of blast furnace important equipment, may facilitate stops up the taphole, in order to next smelting.
液压泥炮是炼铁高炉的重要设备之一，可方便的将出铁口堵住，以便下一次冶炼。
Additionally, the applications of electrical gun in high pressure physics are also given.
最后介绍了电炮在高压物理中的应用。
Mechanical autofrettage process is an efficient approach to enhance the elastic carrying capacity and prolong the fatigue life of gun barrels and high pressure vessels.
机械自紧是提高火炮身管和高压容器承载能力，延长疲劳寿命的有效方法。
The dynamic characteristic of the pressure sensor is very important to the veracity of sensor in the pressure measurement of a certain gun.
在对炮口冲击波测试中，压力传感器的动态性能指标是否满足测量要求至关重要。
Feedback control of the pressure within the electron gun is performed by directly measuring temperature at an internal of the pierce-type electron gun.
通过直接测定上述皮尔斯电子枪内部温度，来反馈控制电子枪内部的压力。
Accessory Configuration: Air cooling argon arc welding gun, argon pressure reduction flow meter.
附件配置：水冷或气冷氩弧焊枪，氩气减压流量计。
Accessory Configuration: Water cooling or air cooling argon arc welding gun, argon pressure reduction flow meter.
附件配置：水冷或气冷氩弧焊枪，氩气减压流量计。
Accessory Configuration: Water cooling or air cooling argon arc welding gun, argon pressure reduction flow meter.
附件配置：水冷或气冷氩弧焊枪，氩气减压流量计。
应用推荐