Such a gate length would keep Moore's law rolling for several years.
这样的“门”深足以让摩尔定律发挥多几年的作用。
From the western gate aforesaid the highway, as every Wintoncestrian knows, ascends a long and regular incline of the exact length of a measured mile, leaving the houses gradually behind.
从前面提到的西大门开始，所有的温顿·塞斯特人都熟悉的那条大道，向上延伸到一个长达一英里的长方形斜坡，渐渐地把那些房屋抛在后面。
Source and drain regions in the semiconductor may define a transistor gate length.
在半导体中的源极区和漏极区可以限定晶体管栅极长度。
Under this way, the gate length and thickness of Si island of DG device show many different scaling limits for various elements.
在这种方法下，由于各种因素的影响，双栅器件的栅长、硅岛厚度呈现出不同的缩减限制。
Experimental results reveal that the peak value of the output voltage of POSFET increases with extended gate area and decreases as the channel length increases.
实验结果显示，POSFET传感器的输出峰值随扩展栅面积的增加而增大，随沟道长度的减小而增大。
The transmitting window of an ONU is indicated in GATE message where start time and length are specified.
GATE消息指示onu的发送窗口，包括窗口的开始时间和长度。
Depending on the potential distribution in the conductive channel, the influence of changing gate length on the OSIT s operation characteristic is analyzed.
依据导电沟道内的电势分布，分析了栅极长度变化对OSIT工作特性的影响。
Whereas, the existing automatic straightener which is gate type or C type can only straighten micromidi shafts in restraint of the length of work top.
而目前国内外普遍采用的门式或C型结构自动校直机受工作台面长度的限制，只能校直中小型轴类零件。
While the gate length of PHEMT device is adequately short, the parasitic resistance across the width of the gate limits the PHEMT device performance.
当PHEMT器件的栅长缩短到足够短的时候，沿着栅宽方向的寄生电阻会影响PHEMT器件的性能。
It is shown that, as the gate length decreases, the gap width between the gates increases and the depth of the channel becomes shorter, the transmitted charge handling capacity will drop from 6.
结果表明，随着栅长减小、栅间隙长度增加和沟道深度减小，传输栅电荷容量约从6。
Then using CAE analysis and through adjusting the gate position, weld lines can be optimized to the minimum length, and this result has also been identified by practice.
进而应用CAE软件进行分析，通过调整浇口位置，对熔接痕的长度进行优化，使其减少到最小，结果得到实践验证。
It was constructed that an optimal problem for gate locations of injection molds based on the introduction of the equivalent flow length concept.
文中通过引入等效流长的概念，建立了浇口位置优化问题。
The gate length and the dimension of the gate head can be controlled in the T-shaped gate processing, and good process controllability and high yield can be achieved.
在该T型栅工艺中栅长和栅帽的尺寸分别进行控制，实现了较好的工艺可控性和较高的工艺成品率。
With the increase of the beam rigidity, the length of the press area and the axes tension force of the beam near the gate-hole increase.
随着梁刚度增加，梁端受压区段长度增加，门洞处梁轴向拉力加大；
Three driving modes of different velocity and resolution (AC mode, GATE mode and DC mode) are used to realize both long stroke length and high resolution.
通过三种不同速度和分辨率的驱动方式(AC模式，GATE模式和DC模式)兼顾大行程与高分辨率的驱动。
The gate length may be larger than the minimum specified by semiconductor fabrication design rules.
栅极长度可以比半导体制造设计规则所指定的最小值大。
Notably, the first length of the first gate is different from the second length of the second gate.
第一栅极的第一宽度与第二栅极的第二宽度不同。
Full-Port ball valves provide pressure drop equal to equivalent length of pipe, and even slightly better than gate valves.
不缩径全流道球阀具有不影响整个管道压降的性能，在此方面，甚至比闸阀性能更加优异。
Second, the method determines the optimum valve gate location in each sub-moulding by applying equal-flow-path-length algorithm.
然后按照等流长算法求各分区的最佳阀浇口位置；
Second, the method determines the optimum valve gate location in each sub-moulding by applying equal-flow-path-length algorithm.
然后按照等流长算法求各分区的最佳阀浇口位置；
应用推荐