This special welding machine makes the welding process of front beam stable and continuous and improves the welding quality greatly.
保证了前机梁焊接过程持续、稳定，提高了前机梁的焊接质量。
Still, they were just as capable of firing a tractor beam at your brain and holding you in front of the television set as Portal or BioShock.
至今为止，这些游戏的魅力丝毫不亚于现在的热门大作“入口”或“生化骑兵”，它们像是对你发射了牵引波束一样牢牢的把你吸在电视机前。
My initial ideas focused on laser beam-type duels between friends in front of the camera.
我最初的想法是让朋友们在摄像机前面进行星球大战那样的激光剑格斗。
The aircraft\'s front half contains the beam control/fire control system, developed by Lockheed Martin, and the battle management system, provided by Boeing.
飞机前半部安装了由洛克西德·马丁公司开发的波束控制/火控系统，ABL系统的作战管理系统是由波音公司开发的。
In X-ray crystallography, scientists turn large quantities of a protein or virus into crystal form, placing it in front of an X-ray beam.
运用X射线晶体学，科学家将大量的蛋白质或者病毒转换成了晶体形式，将其置于一束X射线光束之前。
The practice demonstrates that the prediction to adverse geologic condition in front of the heading face by boring radar and BEAM electric method, especially to water-holding condition, is satisfied.
实践表明，采用钻孔雷达和BEAM电法探测技术对隧道掌子面前方的不良地质情况，尤其是含水情况具有较好的预测结果。
The formulas of mode conversion are derived and effects of optical beam power, initial beam width radius and inverse of the radius of curvature of the wave front on the mode conversion are analysed.
导出模式变换公式，分析了光束功率、光束初始的束宽半径和波前曲率半径的倒数对模式变换的影响。
Action of beam between front row pile and back-row pile makes the stress state of double-row piles different from that of cantilever pile.
前排桩受力状态相当于在桩顶增加一个刚性支撑，后排桩受力状态相当于在桩顶施加一个拉杆。
The utility model discloses an exhaust pipe suspension beam structure for front floor of automobile.
本实用新型公开了一种汽车前地板排气管挂梁结构。
The front view, in latticework 40x40cm, there is a metallic pinky red beam.
前立面是一个40乘以40的方格子结构，散发出一种金属粉红色的光芒。
The front longitudinal beam is the main energy absorber during crash of the vehicle.
在汽车碰撞过程中，汽车前纵梁是主要的吸能装置。
Since the photon shutter in the front end blocks all incident beam power, a thermal-stress analysis is vital in the design of the front end.
前端装置中的挡光器将阻挡全部的光束，所以挡光器的热-应力分析在前端区设计中是非常关键的。
The influence of wave-front-distorted pump pulse on the beam quality of the amplified signal pulse in the non-collinear optical parametric amplification(OPA) is numerically simulated.
数值模拟了拍瓦激光器前端非共线光参变放大（OPA）过程中存在波前畸变的抽运光对信号光光束质量的影响。
Can be installed on the left beam between the front and rear wheel.
安装在拖拉机前后轮之间，拖拉机前进方向左侧的顺梁上。
The structure details such as the joint of side pier, anchor key of ties, steel-concrete transition section and front minor cross beam are introduced.
对该桥的边墩接头、系杆锚固键、钢混凝土接头及前次横梁等部分结构的细节设计做简要介绍。
The central suspension beam is always in axis with the front pier.
中间吊架总是在前墩柱中心线处。
This paper gives a plan for sticking strain gages on beam when measuring the load in all directions on front wheels of a tractor, instrument arrangement and method of calibration.
本文介绍了测取拖拉机前轮空间载荷的贴片方案、仪器布置及标定方法。
The width of the tip-tab increases gradually from the front end of the load beam up to the contact part, and decreases gradually after the contact part.
尖端-搭片的宽度从承载梁的前端到接触部逐渐增加且在接触部之后逐渐减小。
The results show that, for a Gaus-sion laser beam, the shock front is a curved surface, the pressures at different radial positions on the wave front are different.
计算表明，对于高斯激光束，冲击波阵面为一曲面，波阵面上不同径向位置的压强是不同的。
A front anticollision beam of an automobile is used for solving the collision problem of a front anticollision structure and the front modeling of the automobile.
一种汽车前防撞梁，用于解决前防撞结构与车辆前部造型冲突问题。
The thin ribs applied in the back reinforcing structure can not only effectively improve the intensity of the weak beam, but also avoid sink marks on the front side of the beam.
本实用新型的背部加强结构薄筋既可以使弱梁的强度有效的增加，又可以避免弱梁的正面不出现缩痕。
The front of the beam expansion system is also provided with a dust proof mirror.
在其扩束系统前面还设有一个防尘镜。
The influence of dynamic thermal effect induced by optical pumping of YAG crystal rod in a pulsed solid laser on the wave front of the output laser beam is studied in this paper.
本文研究了脉冲固体激光器的YAG激光棒光泵浦动态热效应对激光波面的影响。
Front and back transmission shafts are located on top of folding beam to save space.
前后折叠轴安装在折叠杠顶部以节省空间。
Front and back transmission shafts are located on top of folding beam to save space.
前后折叠轴安装在折叠杠顶部以节省空间。
应用推荐