The body density is improred under equal forming pressure;
在相同成型压力下,坯体的密度增高;
Forming pressure, permeability material extrusion strength.
成形压力大,物料渗挤力大。
The forming pressure has no obvious effect on the bending strength of the composite.
成型压力对反应浸渗材料的强度影响不大。
Glass forming pressure needed to provide air pressure, the normal pressure is 6-8 MPa.
杯子成型需要气压提供,正常气压为6 - 8兆帕。需要配三立方空压机。
The electrical conductivity of the sintered body also increases with increase of the forming pressure.
成形压力的增大也会使烧结体的电性能得到提高。
The control object is the optimum forming temperature and it is realized by controlling forming pressure.
优化目标为最佳成形温度,而温度的控制主要通过压力控制来实现。
The influence of powder grain size and forming pressure are discussed for the performance of W-Cu composites.
着重研究了粉末粒度与成型压力对钨铜材料烧结致密度的影响。
The increasing in forming pressure reduces the pore size and porosity, but has little effect on the pore shape.
随着成型压力的增大,多孔钛孔隙尺寸和孔隙度减小,但孔隙形状未发生显著变化。
Forming pressure, inlay pieces should be of sufficient strength to prevent deformation damage, positioning to be reliable.
成形压力大,嵌件应有足够强度,防止变形损坏,定位必须可靠。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
This paper describes the strain character of forming of thin-walled semi-spherical head. According to the deduction of the forming pressure-pad-force formulae is given.
本文从变形分析着手对压制半球形薄壁封头的成形力进行了分析,并得出了压边力的理论计算式。
The important factors influencing the product performance are investigated, including the dosage of cementing agent, forming pressure, material moisture and curing regime.
对影响产品性能的几个重要因素,包括胶凝材料用量、成型压力、物料含水率和养护制度等进行了研究探讨。
The effects on water-absorption and water-desorption of the mixture ratio of diatomite powder and frit particles as well as modifiers, forming pressure and soaking time were studied.
实验中研究了硅藻土与熔块釉粉之比对试样的吸、放水率,吸、放湿气率等的影响;并且探讨了改性剂、成型压力以及保温时间对吸、放水率等的影响。
The method of artificial neural network was utilized to research the coordinating of the process parameters and the prediction of the forming pressure, and the model was established.
利用人工神经网络方法研究了该工艺的参数协调和变形力预测等问题,建立了神经网络预测模型。
The dependences of seepage velocity and bending strength on agglomerant content, forming pressure, particle diameter of the aggregate, soaking time, firing temperature and so on were discussed.
分别从外加粘结剂百分数、成型压力、骨料粒径、保温时间、烧成温度等因素对渗水砖的渗水速度和强度的影响进行了探讨。
By summer 2009, it had found that the problem was caused by rust forming inside a high-pressure pipe in the power steering system.
直到2009年夏天,这一问题被发现是由于转向动力系统的高压管路生锈引起的。
Now, at some point the pressure becomes big enough that I start to see liquid forming.
现在,在某个点,压强足够的大,我们发现液体开始形成。
As I increase the pressure, I am forming liquid.
当我增加气压时,液体形成了。
Ionized molecular hydrogen can be seen evaporating from the tips of these star-forming columns of gas and dust, under pressure of ultraviolet light from the nebula's central blue giant stars.
在来自星云中心蓝巨星紫外线辐射的压力下,这些由气体和尘埃组成的恒星形成区域尖端的电离氢分子将不复存在。
She's finally shed the stifling pressure garments she wore 23 hours a day to keep scar tissue from forming; last year she finished five years of rehab treatments.
到了去年,她终于完成了长达5年的康复疗程。
It is demonstrated that there exists a part of high pressure on the body surface of the rocket near the fore-located nozzles, thus forming a overturning moment.
指出,当超音速飞行时,在前喷管附近的弹体表面上产生一个局部高压区,由此形成一个翻转力矩。
The solidifying defects after filling can be easily erased by the pressure during the forming.
在成形过程中压力容易消除粘结体充填后的凝固缺陷。
This paper presents the principle, advantages and typical application of internal high pressure forming (IHPF), sheet hydroforming, warm hydroforming and shell hydroforming.
介绍了内高压成形、板料液力成形、热态压力成形和壳体液力成形技术原理、优点和典型应用。
Finally, the simulation results are verified, and the optimal internal pressure forming curve is built as the reference for the practical tube bending.
最后对模拟结果进行了试验验证,并建立了可供实际推弯工艺参考的最佳内压力成形曲线图。
The processing conditions of forming composites such as time, pressure and temperature influence the matrix's impregnating degree.
复合材料的成型条件如成型时间、成型压力、成型温度等影响基体的浸渍程度。
Fluid pressure forming and micro molding technic are expatiated and summarized, including principle, characteristic, current situation, problem and the developing trend in plastic molding field.
对塑性成形领域中的流体压力成形和微成形技术工艺的原理、特点、研究现状、存在的问题和今后的发展趋势进行了阐述和总结。
By simulated test, the co-relationship among the slip granulometric composition, slurry deflocculation curve, mid-high pressure casting forming speed and green body shaping endurance is studied.
通过模拟试验,研究了泥浆的颗粒组成与泥浆的解胶曲线、高中压注浆成形速率及坯体挺形性等的关系。
It is suitable for cutting all kinds of pressure, plastic forming of cardboard and leather products.
它适用于压切各种成形纸板,塑料和皮革制品。
The effect of forming temperature, injection pressure and piston velocity on the filling ability of semi-solid A356 aluminum alloy slurry were investigated.
研究了半固态A356铝合金浆料的成形温度、压射比压和压射冲头速度对半固态A356铝合金流变压铸充填性的影响。
Viscous pressure forming (VPF), a recently developed process, is an advanced approach in sheet metal forming.
粘性压力成形技术是金属板材成形领域里新近出现的一种先进的加工工艺。
应用推荐