ANSI flange sealing principle is very simple: bolt two seal face mutual extruding flange gaskets and formed the seal.
ANSI法兰的密封原理极其简单:螺栓的两个密封面相互挤压法兰垫片并形成密封。
The structure and operation of the ring gasket used in the high pressure flange seal were briefly stated in this article.
概述了高压法兰透镜垫密封的结构和运行状况。
Apply to reciprocating motion of hydraulic cylinder piston rod sealed device can also be used to cover the static flange seal.
适用于液压缸活塞杆往复运动用密封装置,也可用于法兰端盖的静密封装置。
ANSI flange sealing principle is extremely simple: the two bolts each other extrusion flange sealing surface and form a seal gasket.
ANSI法兰的密封原理极其简单:螺栓的两个密封面相互挤压法兰垫片并形成密封。
The manufacturability of a fixing cover with flange seal was analyzed. The general structural design and layout scheme of a progressive die for the cover were presented in detail.
分析了带凸缘密封固定盖的工艺性,介绍了级进模总体设计结构和排样设计。
Flange surface roughness of the influence, especially sealing effect when using the soft cushion, seal surface coarse degree value big are caused by the leak is one of the main reasons why.
法兰表面粗糙度对密封效果影响很大,特别是当采用非软质垫片时,密封表面粗糙的度值大是造成泄露的主要原因之一。
When installing a pinch valve to a rubber, PVC, or any "slick" mating flange, we recommend that you install a metal serrated gasket between the two flanges to assist in the seal.
在安装夹管阀时,如果采用橡胶、PVC或任何“光滑的”配套法兰,则我们建议在两个法兰之间加装一个金属锯齿垫圈以增强密封效果。
Our company is mainly manufacturing to seal and seal of stainless steel pump, valve, flange etc supporting seals the specialized enterprise.
本公司是一家主要生产进行密封及不锈钢泵、阀、法兰等配套密封件的专业企业。
Then, use the aquarium silicone to seal under the flange around all 4 screw holes and around the pipe hole and screw it down with 4 short wood screws.
接着,用水族箱硅胶把法兰盘底、四个螺丝孔以及管孔周围全都涂抹上,然后钻入四枚木螺钉固定好。
In such cases, a metal gasket also not applicable, because the requirements of the compaction force is too large, caused the bolts, make much deformation flange is not easy to seal.
在这种场合,金属垫片也不适用,因为这时要求的压紧力过大,导致螺栓较大的变形,使法兰不易封严。
Prior to startup, get rid of tape from labyrinth seal end of input shaft, labyrinth seal outer surface of output drive flange and respirator.
启动前应除去减速机输入轴迷宫密封端面和输出传动法兰迷宫密封外圆表面,以及呼吸器上的防锈包装及胶带。
These seals are located within the main flange and seal housing.
这些密封位于主法兰和密封壳里。
In such cases, the metal gasket does not apply, because then the pressing force required is too large, resulting in greater deformation of bolts, so difficult to seal flange.
在这种场合,金属垫片也不适用,因为这时要求的压紧力过大,导致螺栓较大的变形,使法兰不易封严。
This wellhead equipment join style for flange join, Possesses installation convenience, Tear open install rapidly, Seal up dependable, Valve's service life long feature.
本井口装置联接方式为法兰联接,具有安装方便、拆装迅速,密封可靠,阀门的使用寿命长等特点。
The inner cup also has a radially extending flange that engages a radial portion of the elastomeric seal body.
内杯也有凸缘的径向延长从事的弹性体密封径向部分。
Power take - off, squared shaft drive. two stud flange without oil seal gasket.
动力启动方轴传动装置。销法兰。无油密封垫圈。
For decades, the American National Standards Institute ANSI flange design for the oil and gas industry provides a seal applied technology, and effective.
几十年来,美国国家标准学会设计的ANSI法兰已经为石油和天然气工业提供了一种适用的密封技术,而且卓有成效。
If there is leakage at the flange face-seal only, further tightening of bolts will almost never stop any flange joint leak.
如果泄露仅仅出现在法兰面密封上,进一步的螺栓紧固基本上并不会阻止法兰连接部分的泄漏。
In order for the flange joint to maintain a gasket seal.
为使法兰连接保持良好的垫片固定密封。
For example, the main driving axle reducer seal assembly technical requirements: input flange oil seal centerline hole of the center line of the small eccentricity of more than 0.1mm.
例如驱动桥主减速器油封的装配技术要求:输入法兰中心线对油封座孔中心线的偏心度小得超过0.1mm。
Firmly press downward to seat seal on flange.
稳固地向下压将座椅密封压入凸缘中。
The results of the experiments show that the quality of the welding seam between the flange girth of steel beam and the seal plate is very important to the function of the joint;
试验结果表明,钢梁翼缘与封口板之间连接焊缝的焊接质量对节点性能至关重要;
The results of the experiments show that the quality of the welding seam between the flange girth of steel beam and the seal plate is very important to the function of the joint;
试验结果表明,钢梁翼缘与封口板之间连接焊缝的焊接质量对节点性能至关重要;
应用推荐