Tension error tolerance beyond which an error is generated.
张力错误一个错误被产生的容许度。
This slider has Fast Response on the left, and Error Tolerance at the right.
这个滑动条的左端表示更快的响应速度，右端表示更大的容错度。
This takes processing power, so if your phone is a little slow, Error Tolerance might not be the best option.
这需要更强的处理器，所以如果你的手机比较慢的话，那些高容错度可以不是个好的选择。
With a small error tolerance, our experimental results show that the bitrate reduction can reach 25 ~ 55%.
我们的实验结果显示，在允许一些误差的情况下，可以使位元率减少25 ~ 55%。
The requirements of the project on the safety, reliability and error tolerance are fully considered in the system configuration.
系统配置充分考虑了本项目对安全性、可靠性和容错性的要求。
This paper proposes a problem that the error tolerance property of spread spectrum sequence influences the performance of spread spectrum system.
提出了扩频码（序列）容错能力影响扩频系统的性能的问题。
Neural network is used widely in many fields as it' s strong self-adapting, self-learning and error tolerance abilities, with which image recognition is implemented.
由于神经网络技术具有很强的自适应性、学习性和容错性，因此被广泛应用于各个领域。
By the discussion and analysis of system functions and configuration, knowledge representation, error tolerance capability of the system, etc, the features of H-ES and presented.
结合系统功能及结构，知识表达，系统的容错能力等方面的讨论分析，本文展示了H -ES系统的特点。
The traditional trial arithmetic and the graphics arithmetic have many disadvantages, especially the tremendous workload, the bad error tolerance and not having the economic analysis ability.
传统的试算法和图解法工作量大，易产生误差，且无法进行经济分析。
A high-temperature superconductivity (HTS) quasi-hairpin filter with high etching error tolerance was developed, which had better characteristics than other structures on the same etching condition.
研制了一种具有良好刻蚀容差性能的类发夹型高温超导滤波器，在同等刻蚀条件下，达得更高的性能指标。
Threshold error severity levels - Identify threshold error severity levels and design fault tolerance levels in service orchestration around these thresholds.
阀值错误严重级别——定义错误严重级别阈值，并在服务编排中根据这些阈值设计容错级别。
From a pure data perspective, eBay can be described as having a huge number of frequent writes, as well as reads, with an extremely low tolerance for error or inconsistency.
从纯数据的角度来看，eBay可以被描述为具有大量的读、写操作，但对容错性和一致性的要求非常严格。
The error indication and machine stop occur only if such tolerance is exceeded for the time period set in the next parameter(TIME TNESION).
错误指示和机器停止发生只有当是否如此的容许度在下个叁数中被为时间周期组超过。
My biggest weakness was my lack of tolerance for any error.
我最大的缺点是我不能容忍任何错误。
The can bus is very robust, with error detection and fault tolerance, but it carries significant communications overhead and high materials cost.
CAN总线非常可靠，具有差错检测和容错能力，但是通信开销很大，材料成本很高。
This tolerance, is to see his behavior after, to see whether he can do better and better, to surpass himself, both the error he has made and the heart.
这里的宽容，是指去看他以后的行止，他是不是能做得越来越好，超越他自己，无论是曾经犯下的小错误还是内心。
The artificial neural network model with capacity of error-tolerance can improve the reliability considerably.
具有容错能力的人工神经网络结构，可以提高人工神经网络的可靠性。
Authors analyzed uncertainties of error and tolerance, found that it is feasible to describe it by gray uncertainty theory, and solved dimension chain through gray mathematics equation.
作者分析了误差和公差的不确定性，发现它们可用灰色不确定性描述，并应用区间灰数数学方程来作了尺寸链的求解。
Therefore, it also proves that it is correct to apply gray uncertainty to describe error and tolerance.
这也证明了应用灰色不确定性来描述误差和公差是正确的。
Feeding error comprizes phase quantization error produced by digital phase shifter, array tolerance and the error produced by failure element.
馈电误差包括由数字移相器的使用引入的相位量化误差、阵列公差和失效单元引起的误差。
Tolerance restricts manufacturing error of part, and allowance redeems the error that comes into being in the process of product assembly.
容差和工艺余量分别是控制零件制造误差和补偿产品装配累积误差的重要参数。
This Paper describes that how to use tolerance principle to identify the qualified problem of spares after the spares show error in the process through examples.
介绍了零件在加工过程中出现误差之后，如何用公差原则来判断其合格性，并通过实例给出了公差原则的公式化表述方法。
This is within an acceptable range(tolerance) of error, so it's OK.
这是可以接受的错误，所以没问题。
This paper proposes an interpolation algorithm that confines the chord error within a specified tolerance range during the interpolation process by adjusting the feedrate.
作者提出了一种数控机床在插补过程中通过调整进给速度从而将弦差限定在一定的误差范围内的插补算法。
Then by taking the regular square prism as an example, the machining error is analyzed, and the relationship among the length of the lathe tool, the work dimension and the tolerance is obtained.
以车削正四棱柱为例，进行了误差分析，得到了刀具长度与工件尺寸和容许误差间的关系。
Then by taking the regular square prism as an example, the machining error is analyzed, and the relationship among the length of the lathe tool, the work dimension and the tolerance is obtained.
以车削正四棱柱为例，进行了误差分析，得到了刀具长度与工件尺寸和容许误差间的关系。
应用推荐