A kind of novel large liquid discharge pump that takes a pair of conjugate wheel as the working component has been put forward.
提出了一种以一对共轭轮为工作元件的新型大排量液体泵。
Reciprocating pump discharge pipe must be before the start of the valve to open.
往复泵启动前必须将排出管路中的阀门打开。
The whole test stand is mainly made of pump stage part, intake part, discharge part and data acquisition part.
整个试验台架由泵级部分、吸入部分、排出部分和数据采集部分组成。
Press out the liquid at this time to overcome the pressure out of pipeline systems with all the necessary resistance to the pressure from the pump discharge.
压出，此时液体带有克服压出管道系统所有阻力所必需的压力从泵中排出。
Do not let pump run for long in the circumstance of discharge valve closed.
注意不要在排出阀关闭的状态下长期运转。
The pump casing shall be suitably ribbed have tangential discharge and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
The pump casing shall be suitably ribbed, have tangential discharge, and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
When the pump is going to stop, first press the stop button (Red), then close the water intake valves and the discharge valve.
停泵时先按下电控箱上泵的停止按钮(红色)，泵停止运转后，关闭管路上的进水阀和排出阀。
Note: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵排泄口，首选的止回阀是管内弹簧负载，带杠杆和压铁或杠杆和弹簧的旋启式止回阀。
The pump casing shall be suitably ribbed have tangent ial discharge and be reinforced to support the weight of the motor assembly.
泵壳应该有适当的肋骨，按切线方向排放，能够再加固以支撑电机总成的重量。
Ctc maximum head is suitable for pump discharge to butanol handling facility.
用户确认泵出口去丁醇处理装置的最大扬程是合适的。
The discharge elbow shall be designed to carry the full weight of the pump, motor and discharge piping.
排泄弯头设计结构应该能够承受泵、电机和排泄管道的全部压力。
This set of components can rotate to the back leakage discharge hole and pump the bottom of the alignment.
这样可以使整套部件旋转至背板漏液排出孔与泵的最底端对齐。
Double screw pump as a positive displacement pump, the pump suction chamber should be closely separated and discharge chamber inside.
双螺杆泵作为一种容积式泵，泵内吸入室应与排出室严密地隔开。
The level of suction pumps for the axial direction, pump discharge outlet may be fitted into the needed horizontal or vertical direction.
泵吸入口为轴向水平方向，泵排出口可根据需要装成水平或垂直方向。
The sludge is passed under a vacuum pump and allows the water to pass through a discharge or recirculation drain.
用真空泵除去污泥的固体含量而该泥水则经排水渠或回流渠排出。
Theoretically the sum of the velocities of the three pistons on the discharge stroke in a low-fluctuation triplex pump should be a constant, and this can be achieved by means of the cam mechanism.
对于三缸低波动往复泵，理论上应使三个活塞在排出行程（吸入行程）中的速度之和为一常数，采用凸轮机构能达到这一目的。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
Close the door distribution discharge valve and, if cut-off valve is opened, pumping water to the piston from the pipeline until the pump output.
关闭分配阀卸料门，如有截止阀则打开，泵送清水至活塞从输送管输出端泵出为止。
In order to prevent damage to the pump must pump discharge pipe into the suction pipe installed between the safety valve.
为了防止泵的损坏，必须在泵的排出管到吸入管之间安装安全阀。
Pump stop, they would first close the discharge stop valve, and switch to a complete halt until pump suction stop valve was closed.
泵停车时，应先关闭排出停止阀，并待泵完全停转后关闭吸入停止阀。
The side of a pump where the suction and discharge valves, pump cylinders, liners, and rods are located.
泵的置有吸入阀和排出阀、泵缸、缸套和拉杆的一侧。
Spring-actuated valve to be used on pump discharge. Swing check with outside lever and spring to be used on sump, sewage and storm drain lines.
弹簧执行机构止回阀用于管道排放。外置操作手柄和弹簧执行机构的旋启式止回阀用于污水坑、排污和雨水排泄管道。
Sludge pump for discharge of sludge, but also with a larger particle size in the discharge of solid water.
污泥泵适于排放污泥，也适用于排放含较大粒径固体的水。
The rotary motion of a profiled impeller in combination with a shaped pump housing or volute applies centrifugal force to discharge fluids from the pump.
成型叶轮的旋转运动以及成型的泵壳或蜗壳产生离心力从泵中排出流体。
Release discharge bolt to discharge the retained water if the pump will not be used for long.
长期停止使用时，应打开放水螺塞，将泵内的剩水排尽。
Typically, the unloader is mounted directly on the discharge side of the pump.
特别是减压器是直接安装在泵边上的。
In order to reduce the fluctuation of pressure and discharge capacity of the triplex drilling pump, the air accumulator is often fixed on the discharge pipe.
为了降低三缸单作用钻井泵的压力和排量波动，通常在排出管线上安装有空气包。
In order to reduce the fluctuation of pressure and discharge capacity of the triplex drilling pump, the air accumulator is often fixed on the discharge pipe.
为了降低三缸单作用钻井泵的压力和排量波动，通常在排出管线上安装有空气包。
应用推荐