This article introduces the reason why there's existing the distortions of the micro align models and explains what is cross distortion and scan distortion 340 and how to match the different "340".
叙述了340光刻机发生畸变的原因,并解释了什么是交叉畸变,什么是扫描畸变,并对如何进行两台340光刻机的匹配进行了探讨。最后给出了试验数据。
Finally, evaluation is made from the following aspects: mean, entropy, cross entropy, distortion of the correlation coefficients and the feasibility of the method is verified in this paper.
最后从均值、信息熵、交叉熵、扭曲程度、相关系数等方面对融合后图像进行了评价,验证了算法的可行性。
Cutting roll-formed steel C-section to stub columns will produce different extent of cross section distortion along the lengths and cause additional initial geometric imperfections.
把辊轧成型的C形冷弯薄壁型钢构件切割成若干短柱,在短柱中将产生不同程度的歪曲变形,进而引起附加的初始几何缺陷。
You see clearly massive cross-over distortion on the negative side.
你清楚地看到,大规模的跨超过失真在消极的方面。
With the way to solve the distortion effect problem by the flexible foundation method, the distortion stress was calculated after solving the cross-section distortion Angle.
分析畸变效应时采用了弹性地基梁法的求解思路,在求出截面畸变角后,计算畸变应力。
Shrinkage distortion typical for three cuts of lumber is illustrated in this log cross section. Note the curvature of the annual rings in each cut and how that affects the distorted shape .
上面在原木截面上演示了三个典型的切割方式的木材的干缩变形效果,请注意每种切割方式的年轮的朝向以及其对变形形状的影响。
The cross-section distortion of bent tube is very small by using ball filler push bending process, with the ovality less than 1.5%.
运用珠粒填料推弯成形工艺成形出的管材截面畸变程度很小,椭圆度不超过1.5%。
At the same press bending Angle, the cross section distortion of the tubes decreases by increasing the distance between the die fulcrums.
在相同的压弯弯曲角度下,增大凹模支点的间距可以减小管坯截面的畸变。
The results show that the severe cross section distortion takes place much easier in the thin-walled rectangular tubes than that in the circular tubes and plank stuff.
结果表明,与圆管、板材等型材的压弯相比,薄壁矩形断面管压弯更容易产生严重的截面畸变;
According to the deformation of single cell box girder cross-section, the displacement parameters were designed, and the displacement modes of cross-section distortion angles were deduced.
根据单箱单室箱梁截面的变形,设计位移参数,导出横截面横向、竖向畸变角的变位模式。
If discovered that has breaks the silk, to break the stock, the external corrosion, the kinking, the cross section serious distortion to replace the steel wire promptly, do not continue to use.
如果发现有断丝、断股、外部腐蚀、扭结、断面严重变形应及时更换钢丝绳,不得继续使用。
And the shot peening surface micro morphology is acute deformation of surface microstructure, lattice distortion and bidirectional cross-slip;
喷丸表面微观形貌为表层组织剧烈变形、晶格扭曲和双向交滑移;
As you can see, there is no more cross-over distortion, even at 100ma idle current.
你可以看到,有没有更多的跨超过失真,甚至在一百毫安闲置电流。
As you can see, there is no more cross-over distortion, even at 100ma idle current.
你可以看到,有没有更多的跨超过失真,甚至在一百毫安闲置电流。
应用推荐