Changing the mesh of the timing gear and the crankshaft gear allow intake timing adjustment relative to the crankshaft position.
改变网格的时间齿轮和曲轴齿轮允许摄入量的调整时间相对曲轴的立场。
For modern injection and ignition systems used in diesel and gas engines it is crucial to know the exact crankshaft position at all times.
对于现代柴油机或内燃机上采用的燃油直喷或点火系统而言，时刻准确地判断其机轴的位置是非常重要的。
When obtain piston position signal from Crankshaft, Top Dead Center Sensor and Crankshaft position Sensor tend to be integrative in structure.
从曲轴上获取活塞位置信号时，所使用的上止点传感器及曲轴转角传感器在结构上趋向于一体化。
The flywheel marks and indentation are used for setting the valve and the ignition systems relative to prescribed position of the crankshaft.
飞轮标记与凹口可以用来确定阀门与点火装置系统的位置，其要根据曲轴的规定位置来确定。
Position drive plate on the crankshaft's dowel pin and press on to the crankshaft flange.
将传动盘安放在曲轴的定位销上，然后压到曲轴法兰上。
The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening.
发动机关键工位螺栓包括连杆螺栓、曲轴螺栓、主轴承盖螺栓、气缸盖螺栓、飞轮螺栓和减振器螺栓等均属螺纹联接。
Two kinds of inspection methods of the position error of key slot an gear journal of crankshaft have been proposed.
提出了两种曲轴齿轮轴颈键槽位置误差的检测方法。
The Hall-effect vane sensor is to be primarily used to sense the angle position and the speed of the crankshaft of the automotive engine, in addition to be used in brushless DC motors.
霍尔叶片传感器主要用于检测汽车发动机曲轴位置和转速，此外还可用于检测无刷电机磁极位置及测速等。
The grinding principle of crankshaft journal is introduced, the formation reason of position error is analyzed in detail, and the corresponding measures are proposed as well.
介绍了曲轴连杆轴颈磨削的原理，对其常见的位置误差现象的形成原因进行了分析，并提出了相应对策和办法。
The software mainly processes the rotate speed signal of the crankshaft and camshaft position signal to export ignition control signal.
软件部分主要对曲轴速度信号、凸轮轴基准信号等进行处理计算，输出点火控制信号。
The plurality of cylinder volumes in the cylinder are different according to the Angle change of the position of the piston rotating in the cylinder volumes under the drive of a crankshaft.
汽缸内多个汽缸容积由曲轴带动下旋转的活塞在汽缸容积的位置角度变化而不同。
TDC (top dead center) - the position of the crank and piston when the piston is farther away from the crankshaft.
(上止点)-当活塞离曲轴最远时，曲柄和活塞的位置。
A stress analysis of a diesel engine crankshaft is made by FEM based on dynamics analysis to determine the position of the initial crack and its propagation direction.
在内燃机动力分析的基础上，运用有限单元法，通过对曲轴应力分析，确定了裂纹启裂部位和扩展方向；
A stress analysis of a diesel engine crankshaft is made by FEM based on dynamics analysis to determine the position of the initial crack and its propagation direction.
在内燃机动力分析的基础上，运用有限单元法，通过对曲轴应力分析，确定了裂纹启裂部位和扩展方向；
应用推荐