• This method can also be used to predict the failure probability of the crank pin.

    利用这种设计计算方法可以预测曲柄失效概率

    youdao

  • The equation for calculating minimum tightening torque on the crank pin nut is given.

    给出了曲柄联接螺母最小拧紧力矩计算公式

    youdao

  • The load applied on the crank pin of a beam pumping unit and the failure patterns of the pin are analyzed.

    分析了游梁抽油机曲柄所受载荷失效形式

    youdao

  • With an adjustable crank pin to control the length of stroke. As the bull gear rotates, the rocker arm is.

    惠氏机构电机转动重载齿轮,驱动一个带有可调整销钉曲柄以便控制进、回程的长度

    youdao

  • A mechanical model for calculating the strength of the crank pin on pumping units is established by a rotary coordinate.

    采用坐标系建立了曲柄强度计算力学模型

    youdao

  • The author holds further that the crank pin rotation on conventional pumping units should be assigned in counterclockwise...

    作者还认为,常规抽油机曲柄旋转方向规定为逆时针,并建议研制可调相位角的曲柄平衡重。

    youdao

  • Using the two - level fuzzy comprehensive theory for the realibilty testing of the crank pin in the non - beam pump is discussed in this article.

    利用二级模糊综合评判原理梁式抽油机曲柄可靠度进行预测。

    youdao

  • The undersigned did deem that if the non-parallelism of the crank pin exceeds permissible limitation, crank pin and bearing were caused to be burnt.

    下列署名认为曲柄不平行度超过允许值时会导致曲柄肖轴承烧坏。

    youdao

  • The main causes is analysed for looseness of the threaded connection on pumping unit crank pin and the corresponding preventive measures are proposed.

    文章介绍了多种螺纹联接预紧力控制方法防松措施,从多方面针对性阐述了解决螺纹联接质量的方法。

    youdao

  • The procedures are chamfering both sides of the gudgeon pin and crank pin core and semi-finishing the crank pin bore at a rate of 1000 pieces per hour at 100% efficiency.

    加工工序对活塞曲轴销孔两侧端面角,半精镗曲轴孔,负荷率100%时,生产率小时1000

    youdao

  • Crank-pin should be honed and polished.

    曲柄销应研磨抛光。

    youdao

  • The checkout error of distortion and flexure caused by tapers of crank bore and piston pin eye is analysed. The solution for this problem is put forward.

    针对一般采用几种连杆弯曲扭曲测量方法,就连杆大小端锥度造成的测量误差进行了分析,并提出解决途径

    youdao

  • Based on the analysis of plastic flow law in crankshaft forming, the cause of typical forming defects, i. e. the folding existing in the crankshaft pin and crank arm was found out.

    通过模拟分析曲轴成形塑性流动规律找出了大型船用曲轴拐成形过程中的典型缺陷连杆颈曲柄外侧折叠成因

    youdao

  • The utility model is composed of a land wheel, a driving pin, a driving crank arm, a driving inserted link, a release spring, and a driving ratchet.

    它由传动、传动、传动回位弹簧传动棘轮组成

    youdao

  • The four-bar linkage included in the mechanical steering system of industrial vehicles is composed of the crank of steering gear, longitudinal connecting rod, the arm on kin pin and frame.

    轮式工业车辆机械式转向操纵系统联系转向器与梯形机构的拉杆机构,构造上属于含有两个球铰两个圆柱铰的RSSR机构。

    youdao

  • The four-bar linkage included in the mechanical steering system of industrial vehicles is composed of the crank of steering gear, longitudinal connecting rod, the arm on kin pin and frame.

    轮式工业车辆机械式转向操纵系统联系转向器与梯形机构的拉杆机构,构造上属于含有两个球铰两个圆柱铰的RSSR机构。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定