They can not tell how much the mould clamping force is on earth?
他们不能指示锁紧力究竟是多少？
In using an injection moulding machine, it is best to use the minimal but adequate clamping force f.
使用注射成型机，最好使用最小同时充足的锁模力f。
The more the blasting clamping force is, the more blasting vibration is produced to the adjacent tunnel.
爆破夹制作用越大，邻近隧道产生的爆破振动越大；
Has good heat-resistance and insulation properties of acid, as well as good mechanical properties of elasticity and clamping force.
具有良好的耐酸耐温性能和绝缘性能，以及良好的弹性机械性能和夹持力。
The new swing clamps maintain the total clamping force by a patented self-locking device if hydraulic pressure is cut off or drops.
新的摇摆夹维持专利自锁装置的总锁模力液压如果被切断或下降。
Due to the mold's expansion when in temperature rising its shrinkage when in temperature drop, the clamping force is quite unstable.
模具升温时受热膨胀，降温时又会收缩，使锁模力很不稳定。
Due to the molds expansion when in temperature rising and its shrinkage when in temperature drop, the clamping force is quite unstable.
模具升温时受热膨胀，降温时又会收缩，使锁模力很不稳定。
Due to the mold's expansion when in temperature rising and its shrinkage when in temperature drop, the clamping force is quite unstable.
模具升温时受热膨胀，降温时又会收缩，使锁模力很不稳定。
The artery clamp of the utility model not only has strong clamping force, but also avoids the shearing action to tissues in the closure process.
本实用新型之血管夹不仅夹闭力量强，而且避免了闭合过程中对组织的剪切作用。
The elastic rigidity of rail pad and ballast stiffness of rail and clamping force of fastener are the main factors that cause the widening of gauge.
钢轨垫层和道床的刚度、轨刚度和扣件扣压力是影响轮轨之间作用力和轨距扩大的主要因素。
The factors that influence selection of hydraulic cylinder were analyzed, for example strong demoulding force, mold clamping force, hydraulic cylinder strobe.
分析了影响液压缸选用的主要因素如脱模力、锁模力、液压缸行程。
To the threaded fasteners which bear important load, we should ensure that the the same clamping force was produced no matter how to change the surface treatment.
对于承受重要载荷的螺纹紧固件，应该保证其表面处理方式不论如何变化，都能产生相同的预紧力。
When jigs and fixtures are designed, the clamping system is designed to ensure that the correct clamping force is applied, and that the clamps can be operated quickly but with safety.
在设计钻模和夹具时，要同时设计装夹系统来保证提供恰当的装夹力，并使装夹操作快速而安全。
Aiming at these problems, this paper studies how the original error affects the accuracy, works out its allowable values, and finds out the equation between friction of pins and clamping force.
针对这一问题，本文研究了零件加工误差对动模板合模位置的影响，得出了零件加工误差的许用值范围，并计算了由于销轴摩擦力对合模力放大比的影响关系式。
Clamping force is an important attribute of the clamping unit of a PIMM. It is the maximum force the machine is capable of to keep the mould closed against the cavity pressure during injection.
锁模力是注塑机一个非常重要的参数，它是注塑机在注射过程中保持模具闭合状态以抵御型腔压力所提供的最大压力。
To prevent the rotating movement of the workpiece, the moment at each clamping point caused by the cutting force has to be eliminated by the forces at the clamping points.
为了防止工件的旋转，每一个点由于切削力引起的扭矩都必须用夹持点的力去除。
The paper is to introduce the structure of this kind of clamping apparatus and to state its efficiency of force - increasing and the condition of its self locking through theoretical analyses.
本文对该夹具结构做了介绍，并通过理论分析，指出增力系数和夹具自锁的设计条件。
Thinking for a new clamping-track instrument is put forward according to the force analysis of it in raker.
通过对耙装机卡轨器的受力分析，提出了新型的卡轨器设计思路。
The clamping of the friction disk is caused by the outwardly rolling of the steel ball along the slop rolling track under eccentric force.
离合器摩擦片的压紧是由钢球在离心力作用下沿斜面滚道向外滚动而引起的。
The utility model relates to a tester which can correctly measure the anti-pulling of cable, line elongation and cable clamping holding force.
本实用新型是一种可以对电缆抗拉、线伸长率和电缆卡握裹力都正确测量的测试仪。
Then the sensor is placed in a novel design centering clamping device to deal with the centering and longitudinal force unload problem.
然后将传感器封装在特殊的定心机构里面，初步解决了传感器检测过程中的定心和卸载问题。
Then the sensor is placed in a novel design centering clamping device to deal with the centering and longitudinal force unload problem.
然后将传感器封装在特殊的定心机构里面，初步解决了传感器检测过程中的定心和卸载问题。
应用推荐