Calculation pass depth must be an integer between 1 and the calculation pass number.
计算传递深度必须为1到计算传递数之间的整数。
The calculation pass number is the calculation pass in which this calculation is executed.
计算传递数是执行该计算所在的计算传递。
The calculation pass depth determines how many calculation passes are required to fully compute a calculated cells definition.
计算传递深度决定要有多少计算传递才能完全计算计算单元定义。
Though PASs have been used to achieve spatially resolved data for almost a decade, they still have some shortcomings, such as the complex and limited sampling rate calculation.
虽然被动空气采样器被用来获得了近十年的空间分辨的数据，但是他们仍然有一些缺点，例如采样率计算的复杂性和有限性。
The article mainly describes the automatic elongation control system of steel strip in skin pass mill, including the measurement, calculation and control of strip elongation.
本文主要介绍平整机带钢延伸率自动控制系统，包括延伸率的测量、计算及控制。
Pass, line up the design of the kind diagram to the spare parts, complete the calculation of the material utilization.
通过，对零件排样图的设计，完成了材料利用率的计算。
The pass schedule is the main technological substance in plate and strip production, and is the base of calculation of the rolling mills type selection.
轧制规程是板带生产的主要工艺技术内容，也是轧机机型选择计算的基础。
Mill automation is based on models with neural networks for pass schedule calculation and computation of set points for roll shifting and bending, and parameters for dynamic flatness control.
轧机自动化以神经网络模型为基础进行道次表、弯辊和窜辊设定点、以及平直度动态控制参数的计算。
It keeps the method of calculation rolling pieces and pass design respective - ly from making error by using method of reducing non-linear equations.
采用求解非线性方程组的方法设计孔型尺寸，避免了因轧件尺寸和孔型尺寸分别计算所造成的误差。
As the main clutch, the steering clutch is an wear part in track type construction machines. It should pass through thermal load calculation to ensure adequate thermal capacity and service life.
转向离合器同主离合器一样，是履带式工程机械的易磨损部件，应进行热负荷计算，以保证其有足够的热容量和使用寿命。
This program can be widely used, such as in roll pass design, the imitation of practical production and the calculation of allocating rolls in continuous rolling.
该程序通用性强，除能设计外，还能进行生产模拟计算，连轧配辊计算。
The principle and calculation method to design short-wavelength pass filters with a concept of equivalent refractive index is presented in this paper.
详细介绍用等效折射率概念设计短波通滤光片的原理和计算方法。
A precise pass-size and welded pipe with excellent surface quality can be get when the deformation way of cube-pass and design calculation with surpass trigonometric equation are used.
采用“立方”孔型变形形式，结合简明的超越三角方程进行设计计算，以得到精确的孔型尺寸及高表面质量的焊管。
Harmonic detection is a very important part of APF. Control strategy and performance of APF will be greatly influenced by calculation delay and low-pass filter in many harmonic detection methods.
谐波检测是有源滤波器的一个关键环节，而其中的计算延时和许多谐波检测方法中的低通滤波都会对有源滤波器控制和系统性能造成很大的影响。
Its calculation is based on the beauty pass so whenever a detail was in shade it didn't use enough samples there and the additional passes had zigzagged edges.
抗锯齿的计算是基于beauty通道，所以当建筑细节隐藏在阴影中，它没有足够的样本进行计算，此外增加的通道也是边缘变得弯弯曲曲。
These models and calculation methods can be used for optimum design of Angle steel roll pass and good effect can be obtained.
将这些模型和算法应用于角钢孔型优化设计，可获得较好的效果。
Pass a calculation is excellent to turn behind of the stock fee and the stock rate of turnovers all want significant descend.
通过计算得出优化后的库存费用和库存周转率都要大幅度下降。
Defects in thermal calculation method on which boiler design is based were analyzed. Such defects caused the calculated value of gas temp. at furnace outlet and convection Pass being lower.
论文分析了该锅炉设计所依据的热力方法的缺陷，使炉膛出口和对流烟道烟温的计算值严重偏低；
Study on Calculation Method of Non-interference Cutter Pass for Complex Surfaces with NC Machining;
针对复杂曲面通常采用数控加工方式制造，从复杂曲面的数学模型入手。
Study on Calculation Method of Non-interference Cutter Pass for Complex Surfaces with NC Machining;
针对复杂曲面通常采用数控加工方式制造，从复杂曲面的数学模型入手。
应用推荐